Savant SSC-0012 Quick Reference Guide

SSC-0012 | 009-1288-03 | 190621 1 of 2 45 Perseverance Way, Hyannis, MA 02601
Copyright 2019 Savant Systems, LLC Savant.com | 508.683.2500
Environmental
Temperature 32° to 104° F (0° to 40° C)
Humidity 10% to 80% Relative Humidity (non-condensing)
Dimensions and Weights
Height 1.40 in (3.5 cm)
Width 6.00 in (15.2 cm)
Depth 3.20 in (8.1 cm)
Weight
Net: 0.50 lb (0.22 kg)
Shipping: 1.50 lb (0.68 kg)
Power
Input Power 12V DC 1.5A
Nominal Power 18 Watts
Regulatory
Safety and
Emissions
FCC Part 15 CE C-Tick
RoHS Compliant
Specifications
Box Contents
(1) SmartControl 12 (SSC-0012)
(1) Install Kit (075-0180-xx)
(1) Mounting Plate (074-0577-00)
(4) 6-pin Screw Down Plug-in Connector (028-9352-xx)
(1) 12V DC 1.5A Power Supply (025-0166-xx)
(1) Cable Tie (014-0071-xx)
(1) Regulatory Card (009-1857-xx)
Minimum Supported Release
Savant OS da Vinci 7.0
A
Reset
Button
Press and hold for 5 seconds while powered On
to clear network settings. Status LED will blink
rapidly when reset is complete.
B
Status LED
Blinks Once: No IP Address
Blinks Twice: Waiting for Host Connection
Blinks Three Times: Host Connection Lost
Solid: Connected to Host
A
Ethernet
10/100 Base-T auto-negotiating port with Link/
Activity. LEDs: 8-pin RJ-45 female.
Link LED (left)
O: Ethernet link is not established.
Green Solid: Ethernet link is established.
Green Blinking: Ethernet activity is occurring.
Data Rate LED (right)
O: 10 Mbps data rate
Green: 100 Mbps data rate
B
RS-232
8-pin RJ-45 female. Used to transmit and receive
serial binary data to and from serial controllable
devices. Ports 1-2 RS-232 - CTS/RTS handshaking.
CTS/RTS Handshaking availability based on
component profile. See RS-232 Wiring.
C
IR
Used to send IR signals to control devices with an
IR input or IR receiver via an IR flasher (5V tolerant
only). 6-pin Screw Down Plug-in Connector. See
IR Wiring for important precautions regarding IR
functionality before making any connections.
D
Normally Open / Normally Closed - Relays
6-pin Screw Down Plug-in Connector
Relay
Dry contacts (open/closed) to control devices
requiring basic on/o operation. DC Voltage Max:
30V DC 1A. 6-pin Screw Down Plug-in Connector
E
GPIO (General Purpose Input and Output Ports) 6-pinScrew
Down Plug-in Connector. See GPIO Wiring for pinouts.
GPIO Input
When configured as an input, the processor will
look for a low (<0.8V DC) or high (>2.4V DC) state.
Minimum 0V DC / Maximum 12V DC
GPIO
Output
When configured as an output, the port provides a
binary output of 0-12V DC 150mA max.
F
Input Power 12V DC 1.5A – Connect to included power supply.
G
Cable Lance
Use with included cable tie to secure power supply
connection.
Network Requirements
Savant requires the use of business class/commercial grade network
equipment throughout the network to ensure the reliability of
communication between devices. These higher quality components
also allow for more accurate troubleshooting when needed.
Connect all Savant devices to the same local area network (LAN) or
subnet as the host. Savant recommends not implementing any type
of trac or packet shaping in your network topology for the Savant
devices as this may interfere with performance.
Network Configuration
To ensure that the IP Address will not change due to a power outage,
a static IP Address or DHCP reservation should be configured. Savant
recommends using DHCP reservation within the router. By using this
method, static IP Addresses for all devices can be managed from a
single UI avoiding the need to access devices individually.
Setting DHCP reservation varies from router to router. Refer to the
documentation for the router to configure DHCP reservation.
Reset
Status
A
B
Front Panel
Rear Panel
RS232
Ethernet
1
2
+
IR
6
+
-
5
-
+
4
-
-
1
+
-
2
-
+
3
+
GPIO
21G G
NC
C2
NONO
C1
NC
RELAY
12 VDC
PD1PD2
/ / / /
A B
C D E F G
SmartControl 12 (SSC-0012)
Quick Reference Guide

Savant SSC-0012 Specifications

General

Brand	Savant
Model	SSC-0012
Category	Controller
Language	English