Need help?Do you have a question about the SawGear SGTAB04 and is the answer not in the manual?
Warnings specific to the installation of TigerStop products.
Safety guidelines when using TigerStop interconnects with machinery.
Critical safety precautions to follow during machine operation.
Important caution regarding potentially FATAL DC voltage inside the motor box.
Warning about pinch points and hazards associated with the push feeder.
Maintaining a clean, well-lit area and precautions for hazardous environments.
Essential PPE such as safety glasses, ear protection, and proper apparel.
Safe electrical practices and prohibition of operating under the influence.
Mandate that only qualified personnel should operate the machine.
Details on SawGear tables and the components included for mounting.
Visual guide to assembling SawGear using brackets, bolts, washers, and knobs.
Instructions for trimming the SawGear table to accommodate specific saw movements.
Steps for securely mounting SawGear using the bench mount brackets.
Procedures for easily removing SawGear from its mounted position.
How to fill out and submit the warranty registration form to TigerStop.
Steps required to activate SawGear using an enable code for full functionality.
Explains the critical role of miter saw pivot point alignment for accurate measurements.
Method to verify the miter saw's pivot point alignment using sample cuts.
Guidance on adjusting the saw's back fence to correct pivot point alignment issues.
Steps to utilize SawGear's system for adjusting the pivot point offset.
Completing the pivot point adjustment by cutting and measuring at 45 degrees.
Functions of Soft Start, and miter entry keys (W, X, Y, Z).
How to use keys for entering measurements (Ft, In, /) and lists.
Usage of Calibrate, Stop, Start, and Clear keys for operation and error correction.
Details on display size and how information is shown in Foot and Metric modes.
Initial setup steps: language, measurement system, and saw side selection.
Setting the correct working length during the initial power up sequence.
When and how to perform a 1st power up again if system settings change.
Standard startup procedure for SawGear after the initial setup is complete.
How to start SawGear and manage its automatic power-off and sleep mode features.
How to adjust the contrast of the SawGear power head screen for better visibility.
Steps to set up a password to prevent unauthorized use of SawGear.
Instructions for modifying an existing password if password protection is enabled.
Steps to turn off and remove password protection from SawGear.
Overview of calibrating five key distances between the stop and saw blade.
Procedure for accurately calibrating the distance for straight cuts.
How to calibrate distances for 45° miter cuts using X, Y, and Z dimensions.
Setting the value for incremental adjustments of the stop position.
Basic steps for executing straight and 45° miter cuts with SawGear.
Initial setup for custom miters, starting with entering molding width.
Detailed steps for cutting miters at various angles for moldings.
Completing the custom miter cutting process based on stock width and angles.
Overview of the Crown & Miter Pro feature for molding cuts.
How to turn on the Crown & Miter Pro feature using the [W] key.
Guidelines for listing angles and cut lengths for room molding projects.
Explains the function of the [W] and [X] keys within the Crown & Miter Pro mode.
How to use the [Y] and [Z] keys to set part length and final angle.
A practical example demonstrating the step-by-step process of using Crown & Miter Pro.
How to make small, precise adjustments to the stop position.
Instructions for saving up to 9 dimensions in each of 10 cut lists.
How to input dimensions combining feet, inches, and fractional parts.
Information about the maximum number of characters the LCD display can show.
How to input dimensions using feet and decimal inch values.
How to enter dimensions involving feet and decimal inches.
Procedures for entering and displaying non-standard fractional inch values.
How to input dimensions in millimeters when the system is in metric mode.
How to input negative numbers, typically for increment adjustments.
Using the Clear key to fix mistakes during data entry.
How to handle and resolve range errors ("Too Big", "Too Small").
Steps to re-home the SawGear after experiencing a significant impact.
How to scale the machine to maintain accuracy over longer cutting lengths.
Description of the foldable, height-adjustable, and durable construction of SawGear legs.
To Next Page
General