Scale-Tronix 6702 - Special Programming Features; Entering the Set-Up Mode; Setting Operational Options

below a preset level the "LO BATT™ annunciator light
will blink signalling the operator that the battery is
wearing down. This is a preliminary warming.
Immediate action is not required as there are séveral
weighings left in the battery when the "LO BATT”
warning is activated. The batteries should be replaced
within a few days of this warning.
A second low battery condition is detected when the
voltage fs inadequate to accurately operate the scale.
At this point the "LO BATT” annunciator will continue to
blink, and the scale will display "bAttrý“ on the weight
display accompanied by a series of four long beeps.
This is done to eliminate the possibility of displaying
erroneous weights by preventing the scale from being
used. Ifthe batteries are replaced when the "LO BATT"
signal activates this additional "low-low battery” signal
will never be seen.
The batteries for the models 5002, 6002, 6502, and
6702 are located under an access door on the rear of
the mast. Two "quarter-turn" fasteners hold the cover in
place. Use a dime coin or screwdriver to rotate the
fastener a quarter of a turn. Replace all six (6) of the
cells with fresh alkaline heavy-duty batteries. Be sure
to observe proper polarity of the cells as they are
installed. Replace the cover and fasten securely with
the quarter-turn fastener using a dime or screwdriver.
Depending on the readout configuration the batteries for
the model 5662 may be accessed by removing a cover
or the top of the readout cabinet. These may be size
"D"
or "C” alkaline cells.
The date of battery replacement should be noted on the
battery replacement label provided on the underside of
the cover. In situations where the scale is not used
extensively the batteries should be replaced annually
just as a precaution.
The model 6162 built-in scale employs a rechargeable
nickel-cadmium battery to power the internal printer and
provide operation during power outages. This battery
should last several years in normal operation but will
eventually deteriorate due to age. The replacement
battery is SCALE-TRONIX® part number 360007.
To replace the 6102's battery unplug the readout or tum
off the circuit breaker providing power to the scale.
Press and hold the “ON” pushbutton to switch the scale
"off. Remove the front panel of the readout to expose
the battery. Unplug the battery's white connector from
the power supply board by pulling straight up. Remove
the old battery from its holder (it may be taped in place)
and install the new battery. Insert the new battery's
connector on the exposed power supply pins. Re-attach
the front panel and restore operating power. Turn the
scale back on by pressing the “ON” pushbutton and
observe that the front panel “CHARGE” indicator is lit.
3.70 SPECIAL PROGRAMMING FEATURES
Your SCALE-TRONIX® second generation weighing
scale incorporates a unique feature that lets you
"customize" the scale to best suit your needs. This “set-
up" mode allows the characteristics of the scale to
match your particular requirements. liems that can be
selected include the automatic shut-off time, weight
resolution, weighing units, automatic printing, etc.
3.71 ENTERING THE "SET-UP" MODE
To enter the “set-up” mode start with the scale turned
off. Note the small "ST" logo ("ST") located directly
above the "RE CALL" pushbutton on the front panel of
the readout. This "ST" actually contains a small hidden
pushbutton. Press and hold this “ST" pushbutton on the
front panel while turning the power on with the “ON”
pushbutton. (Use the rocker power switch in place of
the "ON" button on the models 5102 and 6202.) Once
the scale turns on release the "ST“ pushbutton, then
press and release it 5 more times. The scale will
display "SE*UP" and produce a series of four long
beeps. “Set-up" mode has now been entered.
The "RE CALL" pushbutton is used to select the
particular option value. Once this value is selected the
scale can be advanced to the next option by again
pressing the "ST pushbutton or it can be shut-off by
pressing and holding the "ON" pushbutton. (Use the
rocker power switch in place of the "ON" button on the
models 5102 and 6202.) When the scale is turned back
on, normal scale operation will then resume using the
newly programmed features.
3.72 SETTING THE OPTIONS
First enter the "SET-UP" mode as explained above,
4) Press the "ST" pushbutton. The scale will
display “SOFf (software version). Press the "ST"
5002, 5102, 5602, 6002, 6102, 6202, 6502, 6702 13