ADJUSTING
THE
OUTPUT
LEVEL
The
LOC-SO
is equipped with
output
level controls
that
can be adjusted
for
proper
sound level matching. This is
done
by
inserting a small flat blade
or
Phillips head
screwdriver into the gain adjustment holes, located on
top
of
the
LOC-SO.
By turning
clockwise, the gain
for
that
individual channel,
or
the amount
of
sound allowed
to
pass
through the
LOC-SO
is increased. By turning counterclockwise, the gain
for
that
individual channel is decreased.
If
you feel that after increasing the volume
of
your
stereo,
the
sound is
too
quiet, then equally increase
both
the left and right gains
of
the
LOC-SO
until the sound level is adequate. If the sound level is
too
loud with only a slight
increase in stereo volume,
or
distortion (poor sound quality) is noticeable, then equally
decrease the gains
of
the
LOC-BO.
PROFESSIONAL
WIRING
TIPS
Warning: Never work with more than one connection
at a time, as doing so may cause an electrical short
circuit if two incompatible wires are allowed to touch.
Note: Soldering all wiring connections is
recommended over simply twisting and taping
connections. However, if a soldering iron is not
available, butt connectors or wire nuts are
recommended.
Soldering Wires:
Strip back wire ends approximately 1/2" each. If using
shrink tUbing to protect your connection, slip a
1"
section to be used later over one of the wires.
Twist wire ends together. Begin by heating the bare
wires with a soldering iron. Then apply the solder until
it is absorbed into the strands of the wire. Allow wires
to cool and solder to harden. Once cool, cover the
connection with heat shrink tubing if used previously,
or a UL approved electrical tape. Then move on to the
next connection.
Butt
Connectors:
Strip back wire ends approx. 1/4 to 3/8" each. Crimp
one end of the butt connector to one of the wires you
wish to splice. Crimp the other end of the butt
connector to the wire you wish to splice it
to.
Test
crimp by gently tugging on both wires.
~
~~BARE
ENDS
~~SOLDER
~
TUBING
HEAT
SHRINK
Wire Nuts: Twist together both ends
of
the wires you
wish to connect. Slip the wire nut over the wire ends
and twist until it is firmly seated over the wire ends. Test
the connection by gently tugging the wires.
__
~~==~_K
INSERT WIRES, THEN CRIMP
WARRANTY
Scosche Industries, Inc. warrants
this
product
to
be
free
from
defects in material and
workmanship,
for
a period
of
ninety days, from date
of
purchase. All Scosche
products
are sold
with
the
understanding
that
the purchaser has independently determined
the
suitability
of
such
products. This warranty
does
not
cover
any expenses incurred in
the
removal and reinstallation
of
the product. This warranty is offered
to
the original purchaser
of
the
product
only.
This warranty
does
not
apply
to
the
product
which has been damaged
by
accident,
or
which
has been misused, altered,
or
installed improperly.
If the
product
should prove defective within the warranty period return the
product
with sales
slip, postage prepaid
to
Scosche Industries, Inc.
Your dated sales
slip/proof
of
purchase will establish
your
warranty eligibility. Scosche,
at
its
option will replace
or
repair
the
product
free
of
charge and return
the
product
to
you postage
prepaid.
In no event shall Scosche
be
responsible
for
claims beyond
the
replacement value
of
the
defective
product,
or
in any
way
liable
or
responsible
for
consequential
or
incidental damages.
No express warranties and
no
implied warranties, whether
for
fitness
or
any particular use,
or
otherwise,
except
as
set
forth above (which is made expressly in lieu
of
all other warranties)
shall
apply
to
products
sold
by
Scosche.
No
waiver, alteration, addition
or
modification
of
the
foregoing conditions shall
be
valid, unless made in writing and signed
by
an executive
officer
of
Scosche Industries, Inc.
No salesperson, representative
or
agent
of
Scosche is authorized
to
give any guarantee,
warranty
or
make any representation contrary
to
the
above.
To Previous Page
Loading...
