SEA ISUZU FSR User Manual (English)

Questions and Answers:

K
kiara52Aug 5, 2025
What to do if my SEA Truck does not start?
- M
  Monica BaileyAug 5, 2025
  If your SEA Truck doesn't start, there are several things you can check: * The 12/24v start battery might be flat. In this case, charge or replace the battery. * The isolator switch may be in the off position. Cycle the switch and ensure it is firmly in the ‘On’ position. * Ensure the handbrake is on and the brake pedal is depressed while attempting to start. If these conditions are met, diagnostic assistance may be required.
B
blackburnchristopherAug 15, 2025
What to do if my SEA Truck has poor braking performance?
- S
  Suzanne KingAug 15, 2025
  If your SEA Truck has poor braking performance, consider the following: * For vacuum over hydraulic systems, check if the vacuum pump is running when the ignition is turned on and inspect the fuse. * For vacuum over hydraulic systems, verify the brake fluid level and top it up if necessary. * For air brake systems, ensure that the air filter on the compressor is not blocked.
E
Ellen HartAug 25, 2025
How to fix brake deviation in my SEA Truck?
- D
  Douglas MillerAug 25, 2025
  If your SEA Truck is experiencing brake deviation, here are a few things to check: * Ensure tyre pressures are uniform and adjust to the specified pressure. * Address uneven tyre tread wear with wheel alignment and tyre replacement. * Average the load if it is unbalanced. * If the clearance between the brake drum and the brake shoes is uneven, adjustment may be needed.

SEA ISUZU FSR Specifications

General

Brand	SEA
Model	ISUZU FSR
Category	Trucks
Language	English

Summary

Introduction

Safety Notices and Instructions

Electrical Isolation

Explains how the high voltage circuits are isolated for safety.

High Voltage & Low Voltage Isolation

Details methods for isolating high and low voltage systems.

Vehicle Layout and Specifications

Component Specifications

Details specifications for motor, controller, batteries, charger, and range.

SEA-Drive® Layout

Diagram showing the placement of key SEA-Drive® components.

Controls and Display

Drive Mode Selection

Details the operation of the drive mode selector lever.

Instrument Cluster Display

Explains the main display elements like SOC, speedometer, range, and ECO meter.

Display Indicators

Details vehicle state, gear selection, fault indicators, and regen active status.

Charging Display

Explains display elements specific to charging mode, like charge speed.

Charging the Traction Batteries

Charging Safety and Equipment

Covers warnings and connector details for charging the vehicle.

Vehicle Charger Connection Sockets

Describes Type 1 (v1, v2) and Type 2 sockets and their LED indicators.

Disconnecting the Charge Cable

Procedure for safely disconnecting the charging cable.

Kwik Portable Charger

Charger Overview and Specifications

Details the Kwik portable charger's functions, features, and technical specs.

Charger Status and Faults

Explains working status charts and potential fault codes for the charger.

Pre-Start Checks

Pre-Drive Safety Checks

Lists essential safety and operational checks before driving.

Driving the Vehicle

Starting the SEA-Drive® Vehicle

Procedure for powering up the vehicle, including park brake and drive selector.

Vehicle Operation

Details how to select drive/reverse and operate using accelerator/brake.

Regenerative Braking

Regenerative Braking System

Explains automatic and stalk-activated regenerative braking.

Regenerative Braking Limitations

Notes on limitations when the battery is fully charged.

Parking the Vehicle

Parking Procedure

Steps for safely parking the vehicle, including charging.

24V System Power Consumption

Notes on power consumption by lights/radio and battery voltage.

Maintenance

Weekly Maintenance Checks

Covers checks for coolant and heater fluid levels.

Monthly Maintenance Checks

Covers checks for 24V and traction batteries, including discharge cycle.

24V Battery Maintenance

Details inspection and maintenance for the maintenance-free 24V battery.

Fuse and Relay Boxes

Fuse Box (FB01)

Details the layout, ratings, and functions of the vehicle's fuse box.

Relay Box (FB02)

Details the layout, parts, and functions of the vehicle's relay box.

Inspection and Service Scheduling

Scheduled Inspection Intervals

Table detailing scheduled inspections based on mileage or time.

Inspection Item Breakdown

Details general, functional, and under-vehicle checks for service intervals.

Trouble Shooting Guide

High Voltage Safety Warning

Warns against working on high voltage components; only technicians should.

Vehicle Not Starting Issues

Diagnoses and handles issues when the vehicle fails to start.

Performance and Braking Issues

Diagnoses and handles issues causing poor performance or braking.

Steering and Battery Issues

Diagnoses and handles steering problems and repeated auxiliary battery discharge.

Towing Procedure

Vehicle Recovery Methods

Describes methods for recovering the vehicle, specifying wheel positioning.

Towing Cautions and Warnings

Advises tow operators and warns about loss of power steering/air brakes.

Appendix A: Charging Procedure

Charger Plug-in Process

Step-by-step guide for connecting the charger to the vehicle.

Charging Operation and Status

Details the vehicle's response and indicators during charging.

Charger Disconnection and Storage

Procedure for safely unplugging, storing, and handling charger issues.

LED Status Indicators

Explains the meaning of LED colors during charging.

Appendix B: Wall Charger Specs

Wall Charger Specifications

Details input current, wall inlet specifications, and wall plug types.

Appendix C: Emergency Quick Response

Emergency Procedures Overview

Quick guide for crash or damage scenarios.

Power Down & Battery Disconnect

Steps for safely powering down and disconnecting the battery.

Vehicle Recovery & Safety

Covers jacking, towing, and firefighting procedures for emergencies.

SEA ISUZU FSR User Manual

Table of Contents