SEVERIN KA 5994 - Change factory settings; Adjusting the level of water hardness; Automatic switch-off; Changing the espresso temperature

14
142 x 208 mm
Change factory settings
∙ Theunithasvariousfunctionswhichmaybemodiedas
follows:
∙ Turn the unit on and wait until the cup symbols are
permanently lit.
∙ Press the button for 10 seconds to enter the Change
factory settingsmode.Allthreebuttonsashalternately.
∙ Modify the default factory settings as described further
below.
∙ If no input is registered for about 15 seconds, the unit
returns to ‘Ready’ mode.
∙ To return the various functions (water hardness,
automatic switch-off, temperature, amount) back
to their factory settings, press the buttons and
simultaneously, keeping them pressed for three
seconds. The , and buttonsstartashing
and two beep signals are heard. The appliance switches
off.
Adjusting the level of water hardness
∙ Theunitgivesyouadescalingnotication.Depending
on the water quality (lime content), the button will
ashafter600,500(factorysetting)or400cupcycles.
∙ To ensure proper functioning of the descaling
notication,thelevelofwaterhardnessinyourarea
must be set.
∙ The level of water hardness can be set for soft, normal
or hard water.
∙ Enter the Change factory settings mode (see Change
factory settings).
∙ Press brieytoenterthe‘waterhardness’mode.
∙ Press one of the following buttons for 3 seconds to set
the required water hardness:
∙ : soft water (< 8.4 °dH)
∙ : medium hard water (8.4 – 14 °dH)
∙ : hard water (> 14 °dH / 2.5 mmol/l)
∙ After 3 seconds, the buttonashes3timesto
conrmthenewsetting.Theunitreturnsto‘Ready’
mode.
Automatic switch-off
∙ This appliance comes with an automatic switch-off
feature.
∙ The unit automatically switches off after 25 minutes of
non-use.
∙ The duration until automatic switch-off can set at 9
minutes, 25 minutes (factory setting) or 3 hours:
∙ Enter the Change factory settings mode (see Change
factory settings).
∙ Press brieytoentertheAutomatic switch-off
mode.
∙ Press one of the following buttons for 3 seconds to set
the desired auto switch-off time:
∙ : 9 minutes
∙ : 25 minutes
∙ : 3 hours
∙ After 3 seconds, the buttonashes3timesto
conrmthenewsetting.Theunitreturnsto‘Ready’
mode.
Changing the espresso temperature
∙ The temperature of the espresso can be adjusted to low,
medium (factory setting) and high.
∙ Adjust the temperature as follows:
∙ Enter the Change factory settings mode (see Change
factory settings).
∙ Press brieytoentertheChanging the espresso
temperature mode.
∙ Press one of the following buttons for 3 seconds to set
the desired temperature:
∙ : low
∙ : medium
∙ : high
∙ After 3 seconds, the buttonashes3timesto
conrmthenewsetting.Theunitreturnsto‘Ready’
mode.
Changing the espresso amount
∙ The amount of espresso per cup can be adjusted
individually.
∙ Proceed as described in Making espresso, but keep the
or pressed, until the desired espresso amount
has been drawn.
∙ This amount setting is now saved for future cups. The
amount of espresso must be between 15 and 220 ml.
Any other quantities cannot be saved.
∙ The default factory setting is 20 ml/cup.
Cleaning and care
∙ Remove the plug from the wall socket and wait until the
appliance has cooled down.
∙ To avoid the risk of electric shock, do not clean the
appliance with liquids or immerse it.
∙ Do not use abrasives or harsh cleaning solutions.
∙ Allow the panarello to cool down after each use,
then remove and clean it with hot soapy water. The
small aperture on the centre of the panarello must be
unobstructed at all times. If necessary, remove any
blockageusinganeneedle.
∙ Wipe the outside of the steam tube with a damp cloth.
∙ Allowthesieveholdertocooldownsufcientlybefore
tapping its side against a vertical surface to loosen the
grounds before emptying it.
∙ Theindentationsonthelterholderfacilitateremoving
theltersieve;usethengerstopullthesieveoutfrom
above.
∙ Thelterholder,lterinsertsanddriptraymaybe
cleaned in warm water using a mild detergent; do not
clean these parts in a dish-washer.
∙ Remove the water container and pour out any remaining
water. Clean the container with soapy water and dry
thoroughly.
∙ The exterior housing may be wiped with a damp, lint-
free cloth.