: Feb. 9 2004
1
AR-M550/M620/M700 SIMULATION 8 - 22
( ) : Added when the punch unit is installed.
< > : Added when the saddle unit is installed.
Operation/Procedure
1) Select the number corresponding to the target of operation check
with 10-key.
2) Press START key.
The load selected in procedure 1 is operated.
Press [CUSTOM SETTINGS] key to stop the operation of the load.
(When the punch unit is installed)
(When the saddle unit is installed.)
Operation/Procedure
1) Select the number corresponding to the target of operation check
with 10-key.
2) Press [START] key.
3) Enter the adjustment value with 10-key.
4) Press [START] key. (The entered value is stored.)
PI19 Tray lift motor clock detection 2
PI19S Saddle No. 2 paper detection When the saddle unit is
installed
PI20 Oscillation guide clock detection
PI20S Saddle No. 3 paper detection When the saddle unit is
installed
PI21 Staple lead edge detection
PI21S Paper folding HP detection When the saddle unit is
installed
PI22 Staple dive HP detection
PI23 Tray 2 lift motor clock detection 1
PI24 Tray 2 lift motor clock detection 2
PI25 Tray 2 HP detection
MS1 Front door / Upper door open
detection
MS1S Saddle entry port door detection When the saddle unit is
installed
MS2 Oscillation guide close detection
MS2P Punch front door open detection When the punch unit is
installed
MS2S Front door open detection When the saddle unit is
installed
MS3 Safety area detection
MS3S Paper exit door open detection When the saddle unit is
installed
MS4 Shutter close detection
MS4S Saddle staple presence detection
2
When the saddle unit is
installed
MS5S Stitch operation HP detection 2 When the saddle unit is
installed
MS6S Saddle staple presence detection
1
When the saddle unit is
installed
MS7 Cartridge detection
MS7S Stitch operation HP detection 1 When the saddle unit is
installed
MS8 Staple empty detection
MS9 Tray approaching detection
3-3
Purpose Operation test/Check
Function
(Purpose)
Used to check the operation of the load in the finisher
and the control circuit.
Section Finisher
Item Operation
1 SL7 Belt wait solenoid
2 SL6 Wait solenoid
SIMULATION 3-2
FINISHER SENSOR CHECK.
PI10 PI20 PI19 PI9 PI22 PI1 PI14 PI3
PI17 PI12 PI11 MS8 PI21 MS7 PI18 PI5
PI8 PI6 PI7 MS2 MS4 MS1 MS3 PI16
PI15 MS9 PI24 PI23 PI25
(PI2P) (MS2P) (PI1P) (PI3P)
<PI11S><PI15S><PI5S> <PI14S><PI1S> <PI4S> <PI13S>
<PI12S><PI17S><PI7S> <PI18S><PI6S> <PI8S><MS7S>
<MS5S><PI20S><PI19S><PI21S><MS3S><PI9S> <PI2S>
<PI3S> <MS2S><MS1S><MS6S><MS4S>
3 SL5 Paddle solenoid
4 SL3 Buffer exit port solenoid
5 SL2 Buffer entry port solenoid
6 SL1 Flapper solenoid
7 M10 Tray 2 lift motor
8 M9 Entry port transport motor
9 M8 No. 2 transport motor
10 M7 Oscillation motor
11 M6 Staple motor
12 M5 Tray 1 lift motor
13 M4 Stapler shift motor
14 M3 Alignment motor
15 M2 Paper exit motor
16 M1 No. 1 transport motor
17 M2P Punch side resist motor
18 M1P Punch motor
19 SL4S Transport plate contact solenoid
20 SL2S No. 2 paper deflection plate solenoid
21 SL1S No. 1 paper deflection plate solenoid
22 M8S Paper holding motor
23 M7S Stitch motor: Front
24 M6S Stitch motor: Rear
25 M5S Saddle alignment motor
26 M4S Paper positioning motor
27 M3S Guide motor
28 M2S Paper folding motor
29 M1S Saddle transport motor
Press [START] key, and the operation
is started.
Press [CUSTOM SETTINGS] key, and the
operation is stopped.
3-10
Purpose Adjustment
Function
(Purpose)
Finisher (AR-F16) adjustment
Section Finisher
Item Operation
Item Set range
1 Saddle stitch/folding position
adjustment
192 - 208, 1STEP: 0.25 mm
2 Alignment position adjustment 2 - 18, 1STEP: 0.35 mm
3 Staple binding position
adjustment
68 - 132, 1STEP: 0.152 mm
4 Punch center adjustment 37 - 63, 1STEP: 0.15mm
SIMULATION 3-3
FINISHER LOAD TEST. SELECT 1-
AND PRESS START.
2
SIMULATION 3-3
FINISHER LOAD TEST. EXECUTING
.
2
To Next Page
Loading...
