Sharp AR-M550N - Page 283

: Feb. 9 2004
1
AR-M550/M620/M700 SIMULATION 8 - 25
Operation/Procedure
1) Select the number corresponding to the target of operation check
with 10-key.
2) Press [START] key.
The load selected in procedure 1 turns ON for 10sec.
Press [CUSTOM SETTINGS] key to stop the operation.
The copy lamp or CIS is turned on for 10sec and turned off.
NOTE: CIS: only when the DSPF is installed.
Operation/Procedure
1) Select the number corresponding to the target of operation check
with 10-key.
2) Press [START] key.
The load selected in procedure 1 turns ON for 30sec.
Press [CUSTOM SETTINGS] key to stop the operation.
Operation/Procedure
1) Select the number corresponding to the target of operation check
with 10-key.
2) Press [START] key.
The load selected in procedure 1 operates.
Press [CUSTOM SETTINGS] key to stop the operation.
5-3
Purpose Operation test/Check
Function
(Purpose)
Used to check the operation of the scanner lamp and
the control circuit.
Section Optical (Image scanning)
Item Operation
Press [START] key, and the operation is
started.
Press [CUSTOM SETTINGS] key, and
the operation is stopped after 10sec.
5-4
Purpose Operation test/Check
Function
(Purpose)
Used to check the operation of the discharge lamp and
the related circuit.
Section Process
Item Operation
Press [START] key, and the operation
is started.
Press [CUSTOM SETTINGS] key, and the
operation is stopped after 30sec.
SIMULATION 5-3
COPY LAMP TEST. SELECT 1-2, AND PRESS START.
1.COPY LAMP
2.CIS
1
SIMULATION 5-3
COPY LAMP TEST. EXECUTING···.
1.COPY LAMP
2.CIS
1
SIMULATION 5-4
DISCHARGE LAMP CHECK. SELECT 1, AND PRESS START.
1.DL
1
SIMULATION 5-4
DISCHARGE LAMP CHECK. SELECT 1, AND PRESS START.
1.DL
1
6
6-1
Purpose Operation test/Check
Function
(Purpose)
Used to check the operation of the paper transport
system loads and the control circuit.
Section Paper transport (Discharge/Switchback/Transport)
Item Operation
1 MSWPR MSW reset signal
2 HLPR Heater power relay signal
3 DCPR DC power relay signal
4 MM Main motor
5 DM Drum motor
6 DVM Developing motor
7 TURM Transfer separation motor
8 TRM PS front motor
9 POM1 Paper exit motor 1
10 POM2_FW Paper exit motor 2 forward rotation
11 POM2_RV Paper exit motor 2 reverse rotation
12 VPM Paper transport motor
13 RRC Resist roller clutch signal
14 PSBC Brake clutch signal
15 PSPS Separation pawl
16 T1PFC Tray 1 paper feed clutch
17 T2PFC Tray 2 paper feed clutch
18 HPFC Horizontal transport clutch
19 T1PUS Tray 1 pickup solenoid
20 T2PUS Tray 2 pickup solenoid
21 HPLS Relay path clock solenoid
22 T1LUM Tray 1 lift-up motor
23 T2LUM Tray 2 lift-up motor
24 DSKPFC1 Desk paper transport clutch upstream side
25 DSKPFC2 Desk paper transport clutch downstream side
26 M1PFC Tray 3 paper feed clutch
27 M2PFC Tray 4 paper feed clutch
28 M1PUS Tray 3 pickup solenoid
29 M2PUS Tray 4 pickup solenoid
30 M1LUM Tray 3 lift-up motor
31 M2LUM Tray 4 lift-up motor
32 TRC_LCC Desk clutch sync signal
33 FUM Fusing motor
34 MPFPUS Manual pickup solenoid
35 MPFC Manual paper feed clutch signal
36 MPFGS Manual gate solenoid