: Feb. 9 2004
1
AR-M550/M620/M700 SIMULATION 8 - 32
Operation/Procedure
1) Enter the number corresponding to the maintenance timing dis-
play.
2) Press [START] key. The condition entered in procedure 1) is set.
Operation/Procedure
Various print counter values are displayed.
Operation/Procedure
The paper jam/trouble counter value is displayed.
Operation/Procedure
The history of paper jams and misfeed is displayed.
The misfeed history is displayed sequentially from the latest one. The
max. 100 items of misfeed history can be recorded. The data may be
used to identify trouble position.
The latest 100 items of paper jam history are displayed. (Refer to the
jam cause code table below.)
(Jam cause code)
21
21-1
Purpose Setting
Function
(Purpose)
Used to set the maintenance cycle.
Item Specifications Counter
Maintenance timing display Set range
0 Default (Differs depending on the model.) 0 - 999
1 - 300 Maintenance display at 1K - 300K
999 No maintenance display
22
22-1
Purpose Adjustment/Setup/Operation data output/Check
(Display/Print)
Function
(Purpose)
Used to check the print count value in each section
and each operation mode. (Used to check the
maintenance timing.)
Section
Item Counter
TOTAL Total counter
DRUM Drum counter
TONER Toner counter
DEVE Developer counter
MAINTENANCE Maintenance counter
TOTAL OUTPUT Total output quantity
COPIES Copy effective paper counter
PRINTER Printer counter
FAX FAX print counter
I-FAX OUTPUT iFAX print counter
DOC FILING OUTPUT Document filing print counter
RIIGHT SIDE OUTPUT Right paper exit counter
OTHERS Other print counter (List print , etc.)
SIMULATION 21-1
MAINTENANCE CYCLE SETUP. INPUT VALUE 0-999, AND PRESS
START.
0: DEFAULT
1-300: MAINTENANCE CYCLE (1K-300K)
999: FREE
0
SIMULATION 22-1
COUNTER DATA DISPLAY.
TOTAL: ******** DRUM: ******** TONER: ********
DEVE: ******** MAINTENANCE: ********
TOTAL OUTPUT: ******** COPIES: ********
PRINTER: ******** FAX OUTPUT: ********
I-FAX OUTPUT:******** DOC FILING OUTPUT:********
RIGHT SIDE:******** OTHERS: ********
22-2
Purpose Adjustment/Setup/Operation data output/Check
(Display/Print)
Function
(Purpose)
Used to check the total numbers of misfeed and
troubles. (When the number of misfeed is considerably
great, it is judged as necessary for repair. The misfeed
rate is obtained by dividing this count value with the
total counter value.)
Item Trouble
PAPER JAM Number of paper jams
SPF JAM Number of SPF jams
TROUBLE Number of troubles
22-3
Purpose Adjustment/Setup/Operation data output/Check
(Display/Print)
Function
(Purpose)
Used to check misfeed positions and the misfeed
count of each position. (If the misfeed count is
considerably great, it may be judged as necessary to
repair.)
Section Sections other than SPF/DSPF section
Item Trouble Misfeed
Code Description
NO_JAM_CAUSE No jam. Also used to cancel a jam.
TRAY1
Tray 1 paper feed jam (PFD2 not-reached)
PFD2_NM1
PFD2 not-reached jam (Tray 3 feed paper)
PFD2_NM2
PFD2 not-reached jam (Tray 4 feed paper)
PFD2_NAD PFD2 not-reached jam (ADU re-feed paper)
PFD2_ST1
PFD2 remaining jam (Tray 1 feed paper)
PFD2_SM1
PFD2 remaining jam (Tray 3 feed paper)
PFD2_SM2
PFD2 remaining jam (Tray 4 feed paper)
PFD2_SAD PFD2 remaining jam (ADU re-feed paper)
PPD_NMF PPD1 not-reached jam (Manual feed tray feed
paper)
PPD_NT1
PPD1 not-reached jam (Tray 1 feed paper)
PPD_NT2
PPD1 not-reached jam (Tray 2 feed paper)
PPD_NM1
PPD1 not-reached jam (Tray 3 feed paper)
PPD_NM2
PPD1 not-reached jam (Tray 4 feed paper)
PPD_NLC PPD1 not-reached jam (LCC paper feed paper)
PPD_NAD PPD1 not-reached jam (ADU re-feed paper)
PPD_SMF PPD1 remaining jam (Manual feed tray feed
paper)
PPD_ST1
PPD1 remaining jam (Tray 1 feed paper)
PPD_ST2
PPD1 remaining jam (Tray 2 feed paper)
PPD_SM1
PPD1 remaining jam (Tray 3 feed paper)
SIMULATION 22-2
JAM/TROUBLE COUNTER DATA DISPLAY.
PAPER JAM: ******** SPF JAM: ********
TROUBLE: ********
1
1
1
1
To Next Page
Loading...
