■Power supply
Butteries used
Type Model Quantity
Lithium battery CR2032 3
• Be sure to write down any important information stored in the
memory before replacing the batteries.
1. Precautions
Since improper use of the batteries may cause leakage or explosion,
strictly observe the following instructions.
• Insert the battery with its positive side (+) correctly orientated.
• Never throw batteries into a fire because they might explode.
• Keep batteries out of the reach of children.
• When batteries become near exhaustion, remove them from the
Organizer immediately to avoid battery leakage and corrosion in-
side the Organizer.
Because the batteries in the Organizer were installed at the factory,
they may become exhausted before the specified expiration time is
reached.
2. Operating Batteries Replacement
(1) Battery replacement time
When " BATT " is displayed, immediately replace the batteries with
new ones. If the battery level is low, the alarm may not sound, or
similarly the Backlight may not function of remain on for less than the
set interval. Continued use of the Organizer with low batteries can
alter or clear the memory contents. Memory contents may be lost if
the batteries are improperly replaced or if the following instructions
are disregarded.
Caution:
• PC-LINK may not be available when the battery level is low.
• Expense Report (Summary Report) may not be available when
the battery level is low.
• Under the low battery condition, new data entry and editing of
existing data may not be performed in some modes. Also Clock
and other settings may not be mode.
(2) Replacing the batteries
• Make sure the power is turned off before replacing the batteries.
• Do not press ON until the battery replacement procedure is
completed.
• Do not remove all of the batteries at once. Remove and replace
batteries one by one.
1. Press
ON to turn the power off.
2. Loosen the screw (turn counterclock-
wise) and remove the battery holder
cover on the back of the unit.
3. Remove one used battery using a ball-
point pen or similar object.
• Do not use a mechanical pencil or
sharp pointed object.
4. Install one new battery with the posi-
tive side (+) facing up.
5. Repeat step 3 and 4 for replacing each battery.
6. Replace the holder cover and secure with the screw.
7. The power will be turned on 2 to 3 seconds after ON is pressed.
8. Set the clock to the correct time.
Caution:
• Clock settings may be lost when batteries are removed for a
long time.
• Make sure to confirm all settings are set correctly after replac-
ing the batteries.
■[PC LINK]
Using the included Backup/Restore Utility
With SHARP PC Interface software and cable package, you can
Backup data with an IBM compatible personal computer.
What Does PC Interface Software Do?
Backup : Backs up all data in the Organizer to your PC.
Restore : Restores data from a backup file into the Organizer.
System Requirements
Windows 2000 Professional, Windows Me, Windows 98
• 100% IBM Compatible PC
• Pentium 150MHz or higher
• 8MB free hard disk space
• 32MB RAM (64MB for Windows 2000 Professional)
• VGA monitor or better
• Microsoft Mouse or compatible Pointing Device
• 3.5" (90mm) disk drive
• One available serial port with D-sub 9-pin connector
Caution:
• PC-LINK may not be available when the battery level is low.
Connecting Your Organizer to a PC
1. Turn off your PC and the Organizer.
2. Connect the standard 9-pin connector of the PC interface cable to
a COM port on your PC.
• Using a 25-pin connector instead of the standard 9-pin connec-
tor requires an additional adaptor. (Commercially available.)
3. Connect the other end of the PC Interface Cable to the PC inter-
face connector located on the left side of the Organizer.
PC Interface Cable
>>>>> USE FONT <<<<<
Helvetica/ Helvetica-Condensed/ Century-Schoolbook/ Symbol & OriginalFonts: (RingWorld2/RingFont2/Pa
Symbol/PartsCod)
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
To Next Page
Loading...
