REVEL
HAIR MULTI-STYLER
CONGRATULATIONS ON
YOUR NEW REVEL HAIR
MULTI-STYLER.
TROUBLESHOOTING
ALCI OPERATION
ELECTRICITY FLICKERS OR TRIPS
CIRCUIT BREAKER DURING USE.
This dryer is equipped with an Appliance Leakage Circuit interrupter (ALCI), a safety feature that
renders it inoperable under abnormal conditions. Should the dryer turn off in use, press the red Reset
button on the plug and the dryer should function normally. If the dryer does not reset, please check
your circuit breaker. If the issue persists, ensure there are no other appliances plugged in within the
room where the dryer is being used. Do not use the dryer with a power strip.
WARNING: Any other servicing should be performed by an authorized service representative or that
the appliance has no user serviceable parts.
If you must use your hair multi-styler in the bathroom, install a ground fault circuit interrupter (GFCI)
now! A GFCI is a sensitive device designed to react immediately to electric current leaks and stop the
flow of electricity. Your local electrician can help you decide which type is best for you – a portable
unit that plugs into an electrical outlet or a permanent unit installed by an electrician. The National
Electrical Code (NEC) requires GFCIs in bathrooms, garages, and outdoor outlets of all new homes.
Why do you need a GFCI?
Electricity and water don’t mix. If a hair multi-styler falls into water while plugged
in, the electric shock can kill you – even if the hair multi-styler is switched off. A
regular fuse or circuit breaker will not protect you under these circumstances.
A GFCI provides far greater protection.
A GFCI can save your life! The price is well worth it.
Don’t wait. Install a GFCI now!
*GFCI is a sensitive device which reacts immediately to a small electric current leak by stopping the
electricity flow.
This message about...
...can save a life!
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Please read all instructions and warnings prior to use.
Keep this manual as it contains important information for
future reference.
SHARPER IMAGE
®
NAME AND LOGO (INCLUDING THE 77
LOGO, TOMORROW'S TOMORROW, SHARPER IMAGE
®
REVEL, AND CELEBRATE YOUR HAIR) ARE TRADEMARKS OR
REGISTERED TRADEMARKS. DISTRIBUTED BY AND © 2023
MERCHSOURCE, LLC. IRVINE, CA 92618. ALL RIGHTS
RESERVED.
FOR CUSTOMER SUPPORT, PLEASE CALL 1-800-374-2744.
Printed in China.
Scan for more styling tips and guides.
HOW TO USE
SETTINGS
1. To change the airflow speed, press the speed button. The number of illuminated
white lights above the speed button indicate the airflow speed. (Figure G.)
2. To change the heat level, press the heat button. The number of illuminated red
lights below the heat button indicate the heat level. (Figure H.)
3. To use cool shot and lock in styles with cold air, press the cool shot button above
the power switch. The red lights below the heat button will turn off when cool shot
is active. (Figure I.)
CARE INSTRUCTIONS
1. Clean the hair multi-styler regularly to prevent overheating and to ensure optimal
performance.
2. Spot clean only with a dry cloth. Do not expose to moisture or any cleaning
chemicals.
3. To clean the air intake, remove the filter cap from the bottom of the hair
multi-styler. (Figure J.)
4. With the filter cap removed, gently remove any debris from the air intake and
wipe clean with a dry cloth. (Figure K.)
5. Replace the filter cap by sliding it up into place until securely attached.
J. K.
High
Medium
Low
Cool-shot
G. I.
H.
High
Medium
Low
To Next Page
Need help?
General
