What does error E025 mean on Shimano Steps Bicycle Accessories?
If your Shimano Steps Bicycle Accessories display error code E025, it means a genuine drive unit isn't connected, or cables are disconnected. Connect a genuine battery and drive unit, and check the condition of the cables.
What does error E020 mean on Shimano Steps Bicycle Accessories?
If your Shimano Steps Bicycle Accessories display error code E020, there's a communication error between the battery and drive unit. Check that the cable between them is properly connected.
Why is pedaling so stiff on my Shimano Steps Bicycle Accessories?
If you're experiencing stiff pedaling with your Shimano Steps Bicycle Accessories, check these potential causes: * Ensure the tires are inflated to a sufficient pressure by using a pump to add air. * Verify the assist mode is not set to [OFF]; switch to [BOOST]. * The battery may be running low; charge it fully. * Make sure you didn't turn on the power while pressing on the pedal; try turning it on again without pressure on the pedal.
Why does the battery on my Shimano Steps Bicycle Accessories drain so fast?
If the battery of your Shimano Steps Bicycle Accessories quickly loses its charge, it might be nearing the end of its service life. Consider replacing it with a new one.
What does error E011 mean on Shimano Steps Bicycle Accessories and how to fix it?
If you get error code E011 on your Shimano Steps Bicycle Accessories, it indicates an error occurred during system operation. Try turning the power on again.
How to fix E024 error on Shimano Steps Bicycle Accessories?
If your Shimano Steps Bicycle Accessories display error code E024, it indicates a communication issue with the bicycle system. Ensure the cable is not loose or improperly connected.
How to resolve E010 error on Shimano Steps Bicycle Accessories?
If you see error code E010 on your Shimano Steps Bicycle Accessories, it means a system error was detected. Try pressing the power button on the battery to turn it on again.
What to do if Shimano Steps Bicycle Accessories activate temperature protection?
If your Shimano Steps Bicycle Accessories battery overheats, triggering temperature protection, the battery output is turned off. Move the battery to a cool place away from direct sunlight until its internal temperature drops sufficiently. If the problem persists, contact your dealer.
Why is assistance not being provided by my Shimano Steps Bicycle Accessories?
If you are not getting assistance from your Shimano Steps Bicycle Accessories, consider these potential causes: * The battery may not be sufficiently charged, so check the charge level and recharge if needed. * You might be riding on long slopes in summer or carrying a heavy load, causing the battery to overheat; turn off the power and wait before checking again. * Your speed might be too high; assistance is not provided at speeds exceeding the manufacturer's limit. * Ensure you are pedaling, as the bicycle requires pedal operation. * The assist mode may be set to [OFF]; change it to another mode. * Confirm the system power is ON, using the cycle computer or battery power button.
What to do if I get a charging error on Shimano Steps Bicycle Accessories?
If you see a 'Charging error' message on your Shimano Steps Bicycle Accessories, it indicates an issue during charging. Disconnect the charger from the battery, then press the power button. If the error persists, contact an agency.
General| Drive Unit | DU-E8000 |
|---|---|
| Battery Capacity | 504 Wh |
| Maximum Torque | 70 Nm |
| Rated Voltage | 36 V |
| Rated Power | 250 W |
| Battery | BT-E8010 |
| Display | SC-E8000 |
| Assist Modes | Eco, Trail, Boost |
| Compatible Cassette Sprocket | 11-speed |
| Motor Type | Brushless DC |
| Charging Time | 5 hours |
| Compatibility | Shimano Di2 |
| Compatible Chain | HG-X |
Key safety warnings and precautions for proper product use.
Guidelines for safe operation and handling of the bicycle system.
Explanation of different assist levels and their applications.
Instructions for powering the system on and off via battery or computer.
Guide to switching between different assist levels during riding.
Visual guide to all components of the SHIMANO STEPS system.
Steps to connect the system to a smartphone or tablet via Bluetooth LE.
Interpreting error codes indicated by battery LED patterns.
To Next Page
