The provided document describes the SSS Siedle Camera 130/180, a video camera module designed for integration into various Siedle Vario systems, including In-Home bus, Access, or as a standalone system-free camera.
Function Description
The Camera 130/180 serves as a video input device for door communication systems, allowing visual monitoring of the area in front of the camera. It captures video images and transmits them to compatible Siedle Vario modules or other connected displays. The camera features a day/night switchover for optimal performance in varying light conditions, integrated infrared illumination for low-light scenarios, and a 2-stage heating system to prevent condensation or freezing.
A key feature is the ability to adjust the picture excerpt from the camera view (1 to 9) or display a full-screen view (0) using a rotary switch. This allows users to focus on specific areas of interest, such as the top, central, or bottom alignment of the camera's field of view, effectively reducing the camera's pick-up angle to suit different mounting situations.
For security, the Vario modules can be protected from unauthorized access using the pilfer safeguard controller DSC 602- in conjunction with the ZDS 601-.
Important Technical Specifications
The Camera 130/180 is available in several models, including BCM 653-03, BCM 658-02, ACM 673-03, ACM 678-02, CM 613-03, and CM 618-02. The NTSC product versions differ only in terms of the NTSC colour system.
General Specifications:
- Intercom system compatibility: In-Home bus, Access, System-free.
- Colour system: PAL (NTSC for specific versions).
- Protection class: IP 54, IK 10.
- Ambient temperature: -20 °C to +55 °C.
- Height of structure: 15 mm.
- Dimensions (W x H x D): 99 x 99 x 41 mm.
Video and Imaging:
- Image pick-up:
- CMOS sensor 1/3" 728 x 488 pixels (for BCM 653-03, BCM 658-02, CM 613-03).
- CMOS sensor 1/2.7" 1920 x 1080 pixels (for ACM 673-03, ACM 678-02, CM 618-02).
- Resolution:
- 550 TV-lines (for BCM 653-03, BCM 658-02, CM 613-03).
- 600 TV-lines (for ACM 673-03, ACM 678-02, CM 618-02).
- Lens:
- 2.1 mm (for BCM 653-03, BCM 658-02, CM 613-03).
- 1.55 mm (for ACM 673-03, ACM 678-02, CM 618-02).
- Aperture angle:
- Horizontal 130°, vertical 100° (for BCM 653-03, BCM 658-02, CM 613-03).
- Horizontal 175°, vertical 120° (for ACM 673-03, ACM 678-02, CM 618-02).
- Day/night switchover: Automatic.
- Infrared illumination: Integrated.
- Video output: 1 Vss at 75 Ohm (for ACM 673-03, ACM 678-02).
Power and Current:
- Operating voltage: 10-50 V DC (for CM 613-03, CM 618-02).
- Operating current:
- Max. 160 mA (for BCM 653-03, BCM 658-02, CM 613-03).
- Max. 210 mA (for ACM 673-03, ACM 678-02, CM 618-02).
- 2-stage heating: 12 V AC max. 130 mA.
Terminal Assignment:
- BCM 653-.../658-...: Tak (In-Home bus), TbK (camera branch), Ta (In-Home bus), Tb, Vc (Camera actuation), GND, b (Power supply 12 V AC), C.
- ACM 673-.../678-...: V1 (Video signal), V2 (two-wire FBAS), V3 (Camera supply), V4, V5 (Actuation of video output), V6.
- CM 613-.../618-...: +M (Supply voltage 10-50 V DC), -M, Vc (Camera actuation), VKA (Actuation of camera distributor), A1 (Potential-free contact), A1, b (Power supply 12 V AC), C, L/S (Coaxial connection, L=lead, S=shield).
Usage Features
Mounting and Installation:
- Recommended mounting height: Approximately 1.60 m to the centre of the camera.
- The camera's type designation must be legible at the top back of the module, indicating its correct mounting position.
- The camera can be used with different pick-up angles:
- Approximately 130° angle of aperture.
- Approximately 175° angle of aperture in full-screen mode.
- For a 175° angle of aperture, the pick-up angle can be adjusted to any mounting situation by opening the flap on the back of the module with a screwdriver.
- Picture excerpt selection: A rotary switch allows selection of 9 different picture excerpts (1-9) or full screen (0). This feature helps optimize the camera's view for specific installation scenarios, such as top, central, or bottom camera alignment.
Electrical Safety:
- Installation, commissioning, and servicing work on electrical devices must only be performed by a suitably qualified electrician.
- Certain mounting situations should be avoided in video systems to ensure optimal image quality: direct backlight, direct sunlight, very bright image backgrounds, highly reflective walls opposite the camera, or direct light sources/lamps.
System Integration:
- The camera module is designed for easy integration into Siedle Vario systems. Installation and programming details are provided in the relevant system manual and included with the line rectifier/server.
- For CM 613-.../CM 618-... models, the supply voltage is 10-50 V DC. For other models, a 12 V AC power supply is used.
Maintenance Features
Servicing and Exchange:
- If a camera needs to be exchanged, it can be easily unplugged from the terminal block and replaced.
- When exchanging an existing camera module (CMC 611-...) for a CM 61x-... module, installation only needs to be performed at the door station. The terminals "-" and Vc must be bridged to terminals "-" and Vc at the TLM 612-...
- The product information includes details on the camera module, terminal block, and this product information itself.
Continuous Operation:
- The camera is designed for continuous operation, ensuring reliable performance over time.
- The 2-stage heating system helps maintain functionality in cold environments by preventing condensation and ice formation.
To Next Page
Need help?
General
