Siemens G130 - Fig. 3-160 7950 - Fixed values, binary selection (r0108.16 = 1 and p2216 = 2)

SINAMICS G130/G150 List Manual (LH2), 07/2016, A5E03263479A
1279
3 Function diagrams
3.18 Technology controller
Fig. 3-160 7950 – Fixed values, binary selection (r0108.16 = 1 and p2216 = 2)
- 7950 -
Function diagram
87654321
fp_7950_51_eng.vsd
DO: SERVO, VECTOR, VECTOR3P, VECTORM2C, VECTORMV
SINAMICS
07.01.15 V04.08.00
Technology controller - Fixed value selection binary (r0108.16 = 1 and p2216 = 2)
0 1 1 0
1 0 1 0
1 1 0 0
1 1 1 0
0 0 0 1
0 0 1 0
Tec_ctrl fix val 1
-200.00...200.00 [%]
p2201[D] (10.00)
p2201[D]
0 0 0 0
0 1 0 0
1 0 0 0
<1> p2216 in sight for SERVO and VECTOR only.
<101> The pre-assignment of the sampling time in
p0115[6] is 4000.00 μs.
Tec_ctrl fix val 2
-200.00...200.00 [%]
p2202[D] (20.00)
p2203[D]
Tec_ctrl fix val 3
-200.00...200.00 [%]
p2203[D] (30.00)
p2204[D]
Tec_ctrl fix val 4
-200.00...200.00 [%]
p2204[D] (40.00)
p2205[D]
Tec_ctrl fix val 5
-200.00...200.00 [%]
p2205[D] (50.00)
p2206[D]
Tec_ctrl fix val 6
-200.00...200.00 [%]
p2206[D] (60.00)
p2207[D]
Tec_ctrl fix val 7
-200.00...200.00 [%]
p2207[D] (70.00)
p2208[D]
Tec_ctrl fix val 8
-200.00...200.00 [%]
p2208[D] (80.00)
p2209[D]
p2211[D]
Tec_ctrl fix val 11
-200.00...200.00 [%]
p2211[D] (110.00)
p2210[D]
Tec_ctrl fix val 10
-200.00...200.00 [%]
p2210[D] (100.00)
p2212[D]
Tec_ctrl fix val 12
-200.00...200.00 [%]
p2212[D] (120.00)
p2215[D]
Tec_ctrl fix val 15
-200.00...200.00 [%]
p2215[D] (150.00)
p2214[D]
Tec_ctrl fix val 14
-200.00...200.00 [%]
p2214[D] (140.00)
p2213[D]
Tec_ctrl fix val 13
-200.00...200.00 [%]
p2213[D] (130.00)
Tec_ctrl fix val 9
-200.00...200.00 [%]
p2209[D] (90.00)
(0)
Tec_ctrl sel bit 0
p2220[C]
(0)
Tec_ctrl sel bit 1
p2221[C]
(0)
Tec_ctrl sel bit 3
p2223[C]
(0)
Tec_ctrl sel bit 2
p2222[C]
<101>
0.00 %
0 1 1 1
r2224
Tec_ctr FixVal eff
1 1 1 1
1 1 0 1
1 0 1 1
0 0 1 1
0 1 0 1
1 0 0 1
0 ... 15
2
0
2
3
p2202[D]
p0115[6] (Drive Object)
Tec_ctr FixVal sel
r2225.0
<1>
Tec_ctrl No act
r2229