Siemens G130 - r8939 PN DAP ID; PN DAP ID; p8940[0...239] CBE2 x Name of Station; CBE2 x Name Stat; p8941[0...3] CBE2 x IP address; CBE2 x IP addr

2 Parameters
2.2 List of parameters
SINAMICS G130/G150
884 List Manual (LH2), 07/2016, A5E03263479A
[2] = Number of send net data (bytes) of all connections
[3] = Number of receive subslots of all connections
[4] = Number of receive net data (bytes) of all connections
[5] = Connection type (RT, IRT)
Dependency: Refer to: p8929
Note: For index 5:
Bit 0 = 1: there is at least one RT connection.
Bit 1 = 1: there is an IRT connection.
Description: Displays the DAP ID for the onboard PROFINET interface.
The combination of device ID (r8909) and DAP ID uniquely identifies a PROFINET access point.
Note: DAP ID: Device Access Point ID
List of the SINAMICS DAP IDs:
20008 hex: CBE20 V4.6
20009 hex: CBE20 V4.7
2000A hex: CBE20 V4.8
20108 hex: CU310-2 PN V4.6
20109 hex: CU310-2 PN V4.7
2010A hex: CU310-2 PN V4.8
20308 hex: CU320-2 PN V4.6
20309 hex: CU320-2 PN V4.7
2030A hex: CU320-2 PN V4.8
Description: Sets the station name for the Communication Board Ethernet 20/25 (CBE20/CBE25).
Dependency: Refer to: p8945, r8950
Note: An ASCII table (excerpt) can be found, for example, in the appendix to the List Manual.
The interface configuration (p8940 and following) is activated with p8945.
The parameter is not influenced by setting the factory setting.
Description: Sets the IP address for the Communication Board Ethernet 20/25 (CBE20/CBE25).
Dependency: Refer to: p8945, r8951
r8939 PN DAP ID / PN DAP ID
CU_G130_PN,
CU_G150_PN
Can be changed: - Calculated: - Access level: 3
Data type: Unsigned32 Dyn. index: - Func. diagram: -
P-Group: - Unit group: - Unit selection: -
Not for motor type: - Scaling: - Expert list: 1
Min Max Factory setting
- - -
p8940[0...239] CBE2x Name of Station / CBE2x Name Stat
CU_G130_PN (PN
CBE20),
CU_G150_PN (PN
CBE20),
CU_G130_DP (PN
CBE20),
CU_G150_DP (PN
CBE20)
Can be changed: U, T Calculated: - Access level: 3
Data type: Unsigned8 Dyn. index: - Func. diagram: -
P-Group: - Unit group: - Unit selection: -
Not for motor type: - Scaling: - Expert list: 1
Min Max Factory setting
- - -
p8941[0...3] CBE2x IP address / CBE2x IP addr
CU_G130_PN (PN
CBE20),
CU_G150_PN (PN
CBE20),
CU_G130_DP (PN
CBE20),
CU_G150_DP (PN
CBE20)
Can be changed: U, T Calculated: - Access level: 3
Data type: Unsigned8 Dyn. index: - Func. diagram: -
P-Group: - Unit group: - Unit selection: -
Not for motor type: - Scaling: - Expert list: 1
Min Max Factory setting
0 255 0