Siemens LR16RBQ25 - Page 7

Basic operation en
7
7.4 Switching on intensive mode
If particularly strong odours or vapours develop, you
can use intensive mode.
1.
⁠so oft drücken, bis in der LED-Anzeige die LED4
für die Intensivstufe1leuchtet.
2.
⁠so oft drücken, bis in der LED-Anzeige die LED5
für die Intensivstufe2leuchtet.
a After approx. 6 minutes, the appliance automatically
switches to fan setting 3.
7.5 Switching off intensive mode
▶
To select a fan setting of your choice, press ⁠.
7.6 Switching on the fan run-on
During the fan run-on, the appliance continues to run
for a short time and then switches off automatically.
The fan run-on removes remaining odours and is used
to dry the odour filter after the cooking process.
▶
Press ⁠.
a LED1 for the fan setting lights up in the LED dis-
play. LED6 flashes for the fan run-on.
a The appliance switches off automatically after ap-
prox. 10 minutes.
7.7 Switching off the fan run-on
▶
Press ⁠.
a This immediately stops the fan run-on.
a The appliance switches to the fan setting that was
previously selected.
7.8 Switching on automatic mode
1
The optimum fan setting is set automatically using a
sensor.
▶
Press ⁠.
a In the LED display, LED6 lights up for automatic
mode.
7.9 Switch off automatic mode
1
▶
Press ⁠.
a The appliance switches to the fan setting that was
previously set.
a The ventilation is automatically ended when the
sensor detects no further change in the room air
quality.
a Automatic mode runs for a maximum of four hours.
7.10 Sensor sensitivity
1
In automatic mode, a sensor in the appliance detects
the intensity of the cooking odours and roasting
odours. Depending on the setting of the sensor sensit-
ivity, the optimum fan setting is automatically switched
on.
If the sensor control reacts too weakly or too strongly,
you can change the setting for the sensor sensitivity.
¡ Default setting: Fan setting3
¡ Lowest setting: Fan setting1
¡ Highest setting: Fan setting5
7.11 Setting the sensor sensitivity
1
Requirement:The appliance is switched off.
1.
Press and hold ⁠and ⁠for approx.3seconds.
2.
Press ⁠or to change the setting.
To cancel the setting, press ⁠.
3.
To save the setting, press and hold ⁠and for ap-
prox.threeseconds.
Or wait approx. 10seconds until the setting is
saved automatically.
a A signal tone sounds as soon as the selected set-
ting is saved.
7.12 Intermittent ventilation
In order to regularly ventilate your kitchen, you can use
the interval ventilation. With interval ventilation, the vent-
ilation system switches on and off in the selected set-
ting for the selected time.
Note:This function is only available in the HomeCon-
nectapp.
If the interval ventilation is switched on, LED6 continu-
ously flashes in the LED display for the interval ventila-
tion and the LED for the selected fan setting lights up.
As soon as the ventilation time ends, the LED for the
fan setting you have selected goes out. LED6 contin-
ues to flash.
7.13 Saturation indicator
If the grease filters or odour filters are saturated, cor-
responding symbols flash after the appliance is
switched off.
Note:You can set the saturation indicator in the Home
Connect app depending on the filter used.
Clean the saturated grease filters and, in doing so, ob-
serve the cleaning instructions in these instructions.
Change the saturated odour filters and observe the in-
structions in the accompanying instructions.
If odour filters can be regenerated, follow the instruc-
tions in the accompanying instructions.
7.14 Resetting the saturation indicator
After cleaning the grease filter or after changing the
odour filter, the saturation indicator can be reset.
Requirements
¡ After the appliance has been switched off, LED1
flashes in the LED display for the grease filter satura-
tion display and/or LED2 flashes for the saturation
indicator for the odour filter.
¡ A signal sounds repeatedly.
▶
Press .
a The saturation indicator is reset.
7.15 Setting the saturation indicator
The saturation indicator must be adjusted depending
on the filter used.
Requirement:The appliance is switched off.
1.
Press and hold ⁠and ⁠for approx.three seconds.
1
Depending on the appliance specifications