Siemens LR18RPU25 - Page 7

Basic operation en
7
Or wait approx. 10seconds until the setting is
saved automatically.
a A signal tone sounds as soon as the selected set-
ting is saved.
Resetting the saturation indicator
After cleaning the grease filter or after changing the
odour filter, the saturation indicator can be reset.
Requirements
¡ After the appliance has been switched off, LED1
flashes in the LED display for the grease filter satura-
tion display and/or LED2 flashes for the saturation
indicator for the odour filter.
¡ A repeated signal tone sounds.
▶
Press ⁠ .
a The saturation indicator is reset.
Setting the saturation indicator
The saturation indicator must be adjusted depending
on the filter used.
Requirement:The appliance is switched off.
1. Press and hold ⁠ and ⁠ for approx.three seconds.
‒ To set circulating-air mode (non-regenerable fil-
ter), press ⁠ /⁠ until LED2 lights up in the LED
display.
‒ To set circulating-air mode (non-regenerable fil-
ter), press ⁠ /⁠ until LED3 lights up in the LED
display.
‒ To convert the electronic control back to opera-
tion without the air recirculation filter, press ⁠ /⁠
until LED1 lights up on the LED display.
2. To save the setting, press and hold⁠ and⁠ for ap-
prox. three seconds.
Or wait approx. 10seconds until the setting is
saved automatically.
To cancel the setting, press⁠ .
a A signal tone sounds as soon as the selected set-
ting is saved.
Switching on the lighting
▶
Press⁠ to switch on the lighting.
Note:Colour temperature settings are available in the
HomeConnect
app provided the appliance has this
function.
Switching off the lighting
▶
Switch off the lighting with ⁠ .
Setting the brightness
▶
Press and hold ⁠ or⁠ .
Note:Colour temperature settings are available in the
HomeConnect
app provided the appliance has this
function.
Switching the Ambient Light on
You can switch on the Ambient Light independently of
the ventilation system.
▶
Press⁠ .
Ambient Light – adjusting the
brightness
▶
Press and hold ⁠ until the required brightness is
reached.
Ambient Light – adjusting the colour
You can use the Ambient Light to select a different col-
our of light from a pre-defined colour range.
Note:Additional colours are available in the
HomeConnect
app.
Requirement:The Ambient Light is switched on.
▶
Press ⁠ or ⁠ repeatedly until the required colour is
set.
Switching off the Ambient Light
You can switch off the Ambient Light independently of
the ventilation system.
▶
Press⁠ .
Switching on the button tone
The button tones can be switched on.
Requirement:The appliance is switched off.
1. Press and hold ⁠ and ⁠ for approx.three seconds.
a In the LED display, the LED for the setting that is
currently selected lights up.
2. Press ⁠ or⁠ until LED1 lights up in the LED dis-
play.
To cancel the setting, press⁠ .
3. To save the setting, press and hold ⁠ and⁠ for ap-
prox. threeseconds.
Or wait approx. 10seconds until the setting is
saved automatically.
a A signal tone sounds as soon as the selected set-
ting is saved.
Switching the button tone off
The button tones can be switched off.
Note:Signal tones for the appliance are always
switched on and cannot be switched off.
Requirement:The appliance is switched off.
1. Press and hold ⁠ and ⁠ for approx.three seconds.
a In the LED display, the LED for the setting that is
currently selected lights up.
2. Press ⁠ or⁠ until LED2 lights up in the LED dis-
play.
To cancel the setting, press⁠ .
3. To save the setting, press and hold ⁠ and⁠ for ap-
prox. threeseconds.
Or wait approx. 10seconds until the setting is
saved automatically.
a A signal tone sounds as soon as the selected set-
ting is saved.