Parameter Description Issue 01/06
MICROMASTER 440 Parameter List
62 6SE6400-5BB00-0BP0
Conversion: T-equivalent curcuit -->
L
L
1
k
m
R
R
σ
σ
+=
k
L
L
R
m
m
σ
Γ
=
k
R
R
2
R
R
R
σ
Γ
=
k
L
LL
R
R
S
σ
σ
σσ
+=
Conversion:
L
L
0.51
L
L
)
k
1(1
k
mm Γ
σ
Γ
σ
σΓσ
⋅+=⋅−+=
k RR
2
σΓ
RΓR
â‹…
=
L
5.0
LkL
S σσσσ
â‹…=â‹…=
kL
5.0
kL
)
k
1(
L
R ΓσσΓσσσσ
⋅⋅=⋅⋅−=
equivalent circuitInvers - Γ
Γ Γ
Γ -
T-equivalent curcuitequivalent circuit -->Invers - Γ
Γ Γ
Γ -
% 100 <=>
0305P3
0304P
I 3
V
N
N
â‹…
=
â‹…
=
Z
N
=
ph
V
ph
I
Rated motor impedance:
P0362[3] Magnetizing curve flux 1 Min: 0.0
CStat: CUT Datatype: Float Unit: % Def: 60.0
P-Group: MOTOR Active: Immediately QuickComm.: No Max: 300.0
Specifies first flux value of saturation characteristic in [%] relative to rated motor voltage (P0304).
The parameter settings for the values of P0362 to P0365 respectively P0366 to P0369 are illustrated in the
diagram below.
0
P0366 P0367 100 % P0368 P0369
i
µ
[%]
P0362
P0363
100 %
P0364
P0365
Φ [%]
r0331
[A]i
[%]i
µ
µ
=
Index:
P0362[0] : 1st. Drive data set (DDS)
P0362[1] : 2nd. Drive data set (DDS)
P0362[2] : 3rd. Drive data set (DDS)
Note:
- P0362 = 100 % corresponds to rated motor flux
- Rated flux = rated EMF
- The value belongs to the first magnetizing current value and must be smaller than or equal to
magnetizing curve flux 2 (P0363).
- If the magnetization values entered in P0362 to P0365 respectively P0366 to P0369 do not match the
conditions (see below), a linear characteristic is applied internally.
P0365 ≥ P0364 ≥ P0363 ≥ P0362
P0369 ≥ P0368 ≥ P0367 ≥ P0366
P0363[3] Magnetizing curve flux 2 Min: 0.0
CStat: CUT Datatype: Float Unit: % Def: 85.0
P-Group: MOTOR Active: Immediately QuickComm.: No Max: 300.0
Specifies second flux value of saturation characteristic in [%] relative to rated motor voltage (P0304).
Index:
P0363[0] : 1st. Drive data set (DDS)
P0363[1] : 2nd. Drive data set (DDS)
P0363[2] : 3rd. Drive data set (DDS)
Details:
See P0362 (magnetizing curve flux 1).
Level
4
Level
4
To Next Page
Loading...
