Siemens SIMATIC S5 ET 200U - Page 376

Index-5
ET 200 Distributed I/O Station
EWA 4NEB 812 6087–02b
ET 200U (DP Standard/FMS), 6-1–6-42
ET 200U in a mixed configuration, Mode of the
IM 318–C, 6-4
ET 200U interface module, 1-3
ET 200U(DP Siemens), 1-4–1-9, 4-1–4-36
”DIAGNOSTICS:OVERVIEW” screen,
4-27, 5-30
address IDs, 4-9–4-13
addressing with CPUs 941, 942, 943, 944,
4-7–4-8
area, 4-6
configuring, 4-9
CONFIGURING screen, 4-4
CONTROL function, 4-23
CONTROL with load circuit, 4-23
diagnose problems using COM ET 200,
4-27–4-28
diagnosing faults, 4-25–4-36
diagnosing faults with STEP 5, 4-29–4-36
I/O bus speed, 4-18–4-19
”INDIVIDUAL DIAGNOSTICS” screen,
4-28
manufacturer identification, 4-33
modifying an already configured slave sta-
tion, 4-16
modifying the configuration at a later point,
4-15–4-17
module address, 4-14
module diagnostics, 4-35, 5-38
next available address, 4-7
requirements for operation, 4-2
setting the station number, 4-18–4-19
slow mode, 4-18
start–up, 4-17–4-24
station diagnostics, 4-34
station number area, 4-5
station status, 4-31
station type, 4-6
STATUS function, 4-23
structure of diagnostics, 4-30
SYSTEM START–UP/TEST: STATUS/
CONTROL screen, 4-22
SYSTEM START–UP/TEST:MODULE
SELECTION screen, 4-21
test, 4-17–4-24
using LEDs to diagnose problems, 4-26
ET 200U(DP Standard), 1-4–1-9, 5-1–5-40
”SYSTEM START–UP/TEST:MODULE
SELECTION” screen, 5-24
address IDs, 5-9–5-13
    

addressing with CPUs 941, 942, 943, 944,
5-7–5-8
area, 5-6
BUS FAULT LED, 5-29
configuring, 5-9
CONFIGURING screen, 5-4
CONTROL function, 5-26
CONTROL with load circuit, 5-27
diagnose problems using COM ET 200,
5-30–5-31
diagnosing faults, 5-28–5-40
diagnosing faults with STEP 5, 5-32–5-40
diagnostics messages, 5-25
DP slave parameterization frame, 5-15
I/O bus speed, 5-21–5-22
IM FAULT LED, 5-29
INDIVIDUAL DIAGNOSTICS screen, 5-31
manufacturer identification, 5-36
mode of the IM 318–C, 6-4
modifying an already configured slave
station, 5-19
modifying the configuration at a later point,
5-18–5-20
module address, 5-14
next available address, 5-7
parameterization frame, 5-15–5-16
requirements for operating an IM 318–C, 6-5
requirements for operation, 5-2
RUN LED, 5-29
setting the station number, 5-21–5-22
start–up, 5-20–5-27
station diagnostics, 5-37
station number area, 5-5
station status, 5-34
station type, 5-6
STATUS function, 5-26
structure of diagnostics, 5-33
SYSTEM START–UP/TEST: STATUS/
CONTROL screen, 5-25
test, 5-20–5-27
using LEDs to diagnose problems, 5-29
Index