Siemens Sinamics G120 CU240S DP - BICO Technology Principles

Introduction
1.4 Extended adaptation options using BICO parameters (parameterization for advanced level personnel)
Frequency inverter
Operating Instructions, 08.10. 2008, t.b.d.
15
1.4 Extended adaptation options using BICO parameters
(parameterization for advanced level personnel)
1.4.1 BICO technology: basic principles
Functional principle of BICO technology and frequency inverter closed/open-loop control functions
The inverter software offers a range of open/closed-loop control functions, communication
functions, as well as various diagnostics and operating functions. These functions are
interconnected via internal signal paths and represent the default control structure.
Terminal 5
r0722.0
P0840
ON/
OFF1
DI 0
Figure 1-1 Example: Pre-assigned signal interlocking for digital input 0 of a non-bus-capable Control
Unit
2YHUWHPSH
UDWXUH
'LDJ
QRVWLFV
,
PD[
FRQWURO
0RWRUDQGLQYHUWHUSURWHFWLRQ
$QDORJ
LQSXWV
)LHOGEXV
)L[HG
VHWSRLQWV
0RWRUL]HG
SRWHQWLRPHWHU
-RJ
VHWSRLQWV
,QYHUWHUFRQWURO
'LJLWDOLQSXWV
2SHUDWRU
3DQHO
)LHOGEXV
3,'
FRQWUROOHU
.LQHWLF
EXIIHUV
3RVLWLRQLQJ
UDPS
$XWRPDWLF
UHVWDUW
)UHHIXQFWLRQ
EORFNV
%UDNH
FRQWURO
&RQWUROYLDWHUPLQDOVPHWKRGV
&RQWUROYLDILHOGEXV
5DPSIXQFWLRQ
JHQHUDWRU
6NLSIUHTXHQF\
/LPLWDWLRQ
'&EUDNLQJ
)O\LQJUHVWDUW
9IFRQWURO
9HFWRUFRQWURO
ZLWKRXWHQFRGHU
9HFWRUFRQWURO
ZLWKHQFRGHU
7RUTXHFRQWURO
&ORVHGORRS
FRQWURO
7HFKQRORJLFDOIXQFWLRQV
&RPPDQGVRXUFHV
352),VDIH
)DLOVDIHGLJLWDO
LQSXWV
)DLOVDIHFRPPDQG
VRXUFHV
'LJLWDORXWSXWV
$QDORJ
RXWSXWV
)LHOGEXV
6WDWXV
6HWSRLQWFDOFXODWLRQ
6HWSRLQWVRXUFHV
672
6%&
6/6
66
6DIHW\IXQFWLRQV
9
'&OLQNPD[
&ORVHGORRS
FRQWURO
Figure 1-2 Overview of inverter functions
The functions can be parameterized and interconnected as required. The functions are
interconnected using special software, however, rather than on the basis of electrical circuit
logic by means of cables. The various functions use a range of inputs, outputs, and
parameters.
Enable MOP (raise)
Enable MOP (lower)
MOP output freq [Hz]
MOP
(19.13)
P1035.CDS
r1050
(19.14)
P1036.CDS
Figure 1-3 Example: MOP function (motorized potentiometer)