EasyManua.ls Logo

Siemens SINAMICS G180 - Description; Updating Inverter Software or Instructions; Order Numbers; Type Designations

Siemens SINAMICS G180
62 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
List of messages
Display messages
05/2020, 4BS0576F-004
31
Msg-
Number
Display line 1
Display line 2
Text for event memory entry
Fault sup-
pression on
Description
3206 !! Inverter fault !! Power section W-! IF>Power.Sect.W- as no. 3006, but not retained
3207 !! Inverter fault !! Braking transistor IF>BrakeTransist. as no. 3007, but not retained
3208 !! Inverter fault !! Current asymmetry U IF>C-asymmetry U as no. 3008, but not retained
3209 !! Inverter fault !! Current asymmetry V IF>C-asymmetry V as no. 3009, but not retained
3210 !! Inverter fault !! Current asymmetry W IF>C-asymmetry W as no. 3010, but not retained
3211 !! Inverter fault !! Commun.uP->DSP IF>Comm.uP->DSP as no. 3011, but not retained
3212 !! Inverter fault !! Reset uP-Program Reset DSP Prog. as no. 3012, but not retained
3213 !! Inverter fault !! Reset uP-Commun. Reset DSP Commun. as no. 3013, but not retained
3214 !! Inverter fault !! Reset uP-Watchdog Reset DSP W-D as no. 3014, but not retained
3215 !! Inverter fault !! Reset uP-Interrupt Reset DSP Int. as no. 3015, but not retained
3216 !! Inverter fault !! Commun.DSP->uP IF>Comm.DSP->uP as no. 3016, but not retained
3217 !! Inverter fault !! Current transformer IF>CurrentTransf. as no. 3017, but not retained
3218 !! Inverter fault !! Power unit unknown IF>Pow.Sec. unkn. as no. 3018, but not retained
3219 !! Inverter fault !! Wrong power unit IF>Pow.Sec. wrong as no. 3019, but not retained
3220 !! Inverter fault !! Temperature inside IF>Temp.inside as no. 3020, but not retained
3221 !! Inverter fault !! Temp.Sensor Cool.1 IF>TmpSens.Cool.1 as no. 3021, but not retained
3222 !! Inverter fault !! Temp.Sensor Cool.2 IF>TmpSens.Cool.2 as no. 3022, but not retained
3223 !! Inverter fault !! Temp.Sensor Cool.3 IF>TmpSens.Cool.3 as no. 3023, but not retained
3224 !! Inverter fault !! Temp.Sensor Cool.4 IF>TmpSens.Cool.4 as no. 3024, but not retained
3225 !! Inverter fault !! Temp.Sensor Cool.5 IF>TmpSens.Cool.5 as no. 3025, but not retained
3226 !! Inverter fault !! TempSensorRectifier IF>TmpSens.Rectif as no. 3026, but not retained
3227 !! Inverter fault !! TempSensorCabinet IF>TmpSens.Cabin. as no. 3027, but not retained
3228 !! Inverter fault !! Current control IF>CurrentControl as no. 3028, but not retained
3229 !! Inverter fault !! ResistOutpFilter IF>R-outpFilter as no. 3029, but not retained
3230 !! Inverter fault !! IntermCircFuse IF>IC-fusing as no. 3030, but not retained
3231 !! Inverter fault !! InputReactor 1 IF>InpReactor 1 as no. 3031, but not retained
3232 !! Inverter fault !! InputReactor 2 IF>InpReactor 2 as no. 3032, but not retained
3233 !! Inverter fault !! OutputReactor 1 IF>OutpReactor 1 as no. 3033, but not retained
3234 !! Inverter fault !! OutputReactor 2 IF>OutpReactor 2 as no. 3034, but not retained
3235 !! Inverter fault !! I2C-Bus IF>I2C-Bus as no. 3035, but not retained

Other manuals for Siemens SINAMICS G180

Related product manuals