Siemens SINAMICS S Series - p4031 BI: TM31 signal source for terminal DO 1; TM31 S_src DO 1; p4031 BI: TM15 DI;DO signal source for terminal DI;DO 1; TM15 D S_srcDI;DO 1; p4032 BI: TB30 signal source for terminal DO 2; TB30 S_src DO 2; p4032 BI: TM15 DI;DO signal source for terminal DI;DO 2; TM15 D S_srcDI;DO 2

Parameters
List of parameters
1-782
© Siemens AG 2007 All Rights Reserved
SINAMICS S List Manual (LH1), 07/2007
Description: Sets the signal source for the digital output DO 1 (X542.4, X542.5, X542.6) of terminal module 31 (TM31).
Digital output 1 of TM31 is a relay output.
If the signal at the binector input p4031 is low, then terminal COM 1 (X542.5) is connected to NC 1 (X542.4). This
connection also matches the mechanical quiescent setting of the relay.
If the signal at the binector input p4031 is high, then terminal COM 1 (X542.5) is connected to NO 1 (X542.6).
Note: DO: Digital Output
NC: Normally Closed contact
NO: Normally Open contact
Description: Sets the signal source for terminal DI/DO 1 (X520.3) of terminal module 15 (TM15).
Note: Prerequisite: The DI/DO must be set as an output (p4028.1 = 1).
DI/DO: Bidirectional Digital Input/Output
Description: Sets the signal source for terminal DO 2 (X481.7) of the Terminal Board 30 (TB30).
Note: DO: Digital Output
Description: Sets the signal source for terminal DI/DO 2 (X520.4) of terminal module 15 (TM15).
Note: Prerequisite: The DI/DO must be set as an output (p4028.2 = 1).
DI/DO: Bidirectional Digital Input/Output
p4031 BI: TM31 signal source for terminal DO 1 / TM31 S_src DO 1
TM31 Can be changed: U, T Calculated: - Access level: 1
Data type: Unsigned32 / Binary Dynamic index: - Func. diagram: 1840, 9556
P-Group: Commands Units group: - Unit selection: -
Not for motor type: - Expert list: 1
Min Max Factory setting
- - 0
p4031 BI: TM15DI/DO signal source for terminal DI/DO 1 / TM15D S_srcDI/DO 1
TM15DI_DO Can be changed: U, T Calculated: - Access level: 1
Data type: Unsigned32 / Binary Dynamic index: - Func. diagram: 9400
P-Group: Commands Units group: - Unit selection: -
Not for motor type: - Expert list: 1
Min Max Factory setting
- - 0
p4032 BI: TB30 signal source for terminal DO 2 / TB30 S_src DO 2
TB30 Can be changed: U, T Calculated: - Access level: 1
Data type: Unsigned32 / Binary Dynamic index: - Func. diagram: 9102
P-Group: Commands Units group: - Unit selection: -
Not for motor type: - Expert list: 1
Min Max Factory setting
- - 0
p4032 BI: TM15DI/DO signal source for terminal DI/DO 2 / TM15D S_srcDI/DO 2
TM15DI_DO Can be changed: U, T Calculated: - Access level: 1
Data type: Unsigned32 / Binary Dynamic index: - Func. diagram: 9400
P-Group: Commands Units group: - Unit selection: -
Not for motor type: - Expert list: 1
Min Max Factory setting
- - 0