List of parameters
Parameters
1-793
© Siemens AG 2007 All Rights Reserved
SINAMICS S List Manual (LH1), 07/2007
Note: DI/DO: Bidirectional Digital Input/Output
Description: Sets the mode of the DI/DO of terminal module 17 (TM17).
Note: DI/DO: Bidirectional Digital Input/Output
Description: Sets the mode of the DI/DOs of terminal module 15 (TM15).
12 DI/DO 12 (X521.6) Inverted Not inverted -
13 DI/DO 13 (X521.7) Inverted Not inverted -
14 DI/DO 14 (X521.8) Inverted Not inverted -
15 DI/DO 15 (X521.9) Inverted Not inverted -
16 DI/DO 16 (X522.2) Inverted Not inverted -
17 DI/DO 17 (X522.3) Inverted Not inverted -
18 DI/DO 18 (X522.4) Inverted Not inverted -
19 DI/DO 19 (X522.5) Inverted Not inverted -
20 DI/DO 20 (X522.6) Inverted Not inverted -
21 DI/DO 21 (X522.7) Inverted Not inverted -
22 DI/DO 22 (X522.8) Inverted Not inverted -
23 DI/DO 23 (X522.9) Inverted Not inverted -
p4049 TM17 digital inputs/outputs, set the mode / TM17 DI/DO mode
TM17 Can be changed: T Calculated: - Access level: 2
Data type: Unsigned32 Dynamic index: - Func. diagram: -
P-Group: Commands Units group: - Unit selection: -
Not for motor type: - Expert list: 1
Min Max Factory setting
- - 0000 bin
Bit field: Bit Signal name 1 signal 0 signal FP
00 DI/DO 0 (X520.2) I/O with time I/O -
01 DI/DO 1 (X520.3) I/O with time I/O -
02 DI/DO 2 (X520.5) I/O with time I/O -
03 DI/DO 3 (X520.6) I/O with time I/O -
04 DI/DO 4 (X520.8) I/O with time I/O -
05 DI/DO 5 (X520.9) I/O with time I/O -
06 DI/DO 6 (X521.2) I/O with time I/O -
07 DI/DO 7 (X521.3) I/O with time I/O -
08 DI/DO 8 (X521.8) I/O with time I/O -
09 DI/DO 9 (X521.9) I/O with time I/O -
10 DI/DO 10 (X522.2) I/O with time I/O -
11 DI/DO 11 (X522.3) I/O with time I/O -
12 DI/DO 12 (X522.5) I/O with time I/O -
13 DI/DO 13 (X522.6) I/O with time I/O -
14 DI/DO 14 (X522.8) I/O with time I/O -
15 DI/DO 15 (X522.9) I/O with time I/O -
p4049 TM15 digital inputs/outputs, set the mode / TM15 DI/DO mode
TM15 Can be changed: T Calculated: - Access level: 2
Data type: Unsigned32 Dynamic index: - Func. diagram: -
P-Group: Commands Units group: - Unit selection: -
Not for motor type: - Expert list: 1
Min Max Factory setting
- - 0000 bin
Bit field: Bit Signal name 1 signal 0 signal FP
00 DI/DO 0 (X520.2) I/O with time I/O -
01 DI/DO 1 (X520.3) I/O with time I/O -
02 DI/DO 2 (X520.4) I/O with time I/O -
03 DI/DO 3 (X520.5) I/O with time I/O -
04 DI/DO 4 (X520.6) I/O with time I/O -
05 DI/DO 5 (X520.7) I/O with time I/O -
06 DI/DO 6 (X520.8) I/O with time I/O -
To Next Page
Loading...
