Silca Air4 V Plus 128 - Remote Control Operation; Copying Fixed Codes; Copying Rolling Codes (Normal); Copying Rolling Codes (Secure Learning)

Air4
Copyright Silca S.p.A 2020 8
ENGLISH
ATTENTION: before copying make sure the original remote control is working properly.Check the
state of the baery.
COPY FIXED CODES :
1.Press and hold down buon 1 on the “Air4 V 64-Air4 V Plus 128 ” remote control and at
the same me press buon 4 four mes. 2. Release both buons: the “Air4 V 64-Air4 V Plus
128 ”remote control LED will ash briey about every 2 sec. 3. Place the remote control to be
cloned in front of the “Air4 V 64-Air4 V Plus 128 ”, at a distance of about 2 cenmetres. 4.Press
and hold down the buon to be copied from the original remote control and wait for the “Air4
V 64-Air4 V Plus 128 ”LED to start ashing rapidly, which conrms that the code has been
acquired. This operaon may take a few seconds. 5.While the LED is ashing, press the “Air4 V
64-Air4 V Plus 128 ”buon to which the code must be transferred and hold down unl the LED
goes out.
N.B. •If the LED goes out unexpectedly it means the code has not been acquired. Repeat the
operaon from point 1.• To programme the second “Air4 V 64-Air4 V Plus 128 ”buon, repeat
the operaon from point 1.
COPY ROLLING CODE NORMAL* :Follow the “Fixed Code” instrucons.
COPY ROLLING SECURE LEARNING* :
1. Press and hold down buon 1 on the “Air4 V 64-Air4 V Plus 128 ”and at the same me press
buon 4 four mes. 2. Release both buons: the “Air4 V 64-Air4 V Plus 128 ”LED will ash brie-
y about every 2 sec. 3. Place the remote control to be cloned in front of the “Air4 V 64-Air4 V
Plus 128 ”, at a distance of about 2 cenmetres. 4. Press and hold down the buon to be copied
from the original remote control and wait for the “Air4 V 64-Air4 V Plus 128 ”LED to go on
without ashing and then start double ashing about every 2 seconds. 5.Transmit the original
remote control source code (check the website www.silca.biz to nd the one for the remote
control you want to copy). 6.The “Air4 V 64-Air4 V Plus 128 ”LED will ash rapidly; press the
buon by which the code will be memorised and hold down unl the LED goes out.
(*) Full list of original models at: www.silca.biz.
N.B.: Transmit the source code to copy an “Air4 V 64-Air4 V Plus 128 ”remote control program-
med as “Rolling Secure Learning”.
PROCEDURE A.L.S.:Simplied procedure to acvate the remote control on the receiver. The list
of receivers compable with the procedure can be found on www.silca.biz. For other receivers
see the original instrucons provided by the manufacturer.
N.B.:Follow A.L.S. procedure before using the original remote control.
1.Stand close to the automaon 2.Hold down the programme buon for about 10 seconds;
release when the LED starts to ash 3.Wait unl the LED goes out.
ATTENTION : receivers may have the radio channel disabled. In such cases enter the new re-
mote controls using a manual procedure.
TRANSMISSION OF “Air4 V 64-Air4 V Plus 128 ” SOURCE CODE :
1.Press buons 1 and 2 on the remote control simultaneously for 8 seconds and release when
the LED ashes. 2.While the LED is ashing press the buon for which the source code is requi-
red.
Baery replacement: Use a star screwdriver to loosen the screw on the back of the “Air4 V 64-Air4 V Plus 128
”remote control.The “Air4 V 64-Air4 V Plus 128 ”remote control is powered by a 3V CR2032 LITHIUM BATTERY.
Check polarity-Do not throw at baeries away: dispose of them in the special waste sorng centres.