Prepare outdoor camera for installation
Siqura HSD620/622/626 & MSD620/622
IP PTZ dome with day/night and wide dynamic range
Quick Start Guide
© Siqura B.V. 2014
Version 2.0 (101310-2)
xSD62x QSG (MW10)
Outdoor camera mounting requirements
Install outdoor camera with wall mount
www.siqura.com
www.tkhsecurity-usa.com
22-Pin connector definition
Figure 1 Outdoor camera package contents
CD (Manuals
and software)
Outdoor model with
tube adapter
Screws
(M3, M5 PH, M5 torx)
For operation, an HSD62x/MSD62x camera requires the following:
A Cat 5 Ethernet cable with an RJ-45 connector
- or (for /SFP models) -
An SFP module as described in the XSNet™ SFP data sheet and fiber optic cable
and connectors compatible with the chosen SFP module.
A cable harness for power, analogue video, and audio transmissions, equipped
with a 22-pin connector for connecting to the camera (table 1).
Figure 3 Cable harness components
24 VAC
Ground (GND)
24 VAC
Figure 4 Power input details
Figure 5 22-pin connector pins
RJ-45 connector LEDs
Green indicates a good network connection.
Yellow verifies network activity.
Figure 6 RJ-45
connector LEDs
Input 5 V 10 kΩ pull up
Photo Relay output 300V
Table 1 22-pin connector assignments
Figure 7 WM01A Mini Wall Mount
Use one of two types of mounts to install an outdoor HSD62x/MSD62x on a
wall.
Siqura WM01A Mini Wall Mount
Siqura WM07 Long Wall Mount
Figure 8 WM07 Long Wall Mount
The mini wall mount and the long wall mount can be installed
onto a box mount if extra space for the cables is required.
To prepare the outdoor HSD62x/MSD62x for installation
1. Remove the outdoor tube adaptor by rotating counter clockwise (figure 9a).
2. Make a note of the IP address on the label attached to the cylindrical heat sink.
3. Remove the PE cloth and take off the lens cap.
4. Generously apply the supplied lubricant to the optical cover’s waterproof boot to
ensure an IP66 quality installation (figure 9b).
5. Loosen the screw head alignment pins on the dome cover by turning clockwise
and line up the alignment pin and screws on the optical cover with the holes in
the dome body.
6. Attach the optical cover to the dome body by pressing gently down on the sides
of the dome cover (figure 9c).
7. Turn the screw head alignment pins counter-clockwise with a suitable
screwdriver to lock the dome into place and secure the dome with the included
Phillips-head or torx screw.
Figure 9a
Remove outdoor tube
adapter
Figure 9b
Lubricate optical cover’s
waterproof boot
Figure 9c
Attach optical cover
to dome body
Outdoor installation requires the following items:
Dome camera
Supplied waterproof boot
Wall mount (optional accessory)
Screws and screw anchors
Screwdriver and drill
To mount the outdoor HSD62x/MSD62x with a wall mount
1. Make a hole in the wall or metal access plate for the cables and secure the
supplied cable gland in the wall.
2. Ensure that the weather resistant gasket is correctly attached to the mount.
3. Thread the cables through the wall mount and screw it onto the wall.
4. Attach the waterproof boot to the wall mount.
5. Thread the cables through the outdoor tube adaptor and fix it to the wall
mount with the supplied screws and washers.
6. Clip the safety wire to the dome camera.
7. To keep insects out, block the cable entry hole with the supplied sponge.
8. Connect the cables to the dome camera.
9. Attach the dome to the outdoor tube adaptor and fasten them together with
the supplied screws.
Warning: Fully torque down the mounting bolt that attaches the
WM02 tube adapter to the mounting bracket to prevent any
movement of the camera due to wind, vibration, etc.
Make sure the camera cannot move at all in its bracket after
installation. Any movement of the camera in its bracket can
compromise positional accuracy.
Figure 11 Mini wall mount
Figure 10 Long wall mount
Figure 2 Indoor camera package contents
To Next Page
Need help?
General
