Skiddoü NASJO - Folding, Removal, and Accessories

22
holes.
Folding the pushchair
When folding, the handle should always be on the side of the larger wheels (gure 39).
Method A – with the canopy placed on the same side as the handle
• On the outside, under the footrest, there is a folding mechanism for the seat/carrycot (gure
40). Move the grey slider and at the same time pull the lever (gure 41). Then lift the footrest
up by folding it as far as possible towards the part with the canopy (gure 42, 43).
• In the centre of the frame, there is the mechanism responsible for folding the entire structure.
Move the grey slider and simultaneously pull the lever to activate it. Then lift the whole
pushchair using the handle to fold it (gure 44, 45).
• A pocket in the basket contains a strap to fasten the pushchair during transport. After
folding the pushchair, pull the strap through the frame of the pushchair and fasten it with a
snap (gure 46).
Method B – with the canopy placed on the side opposite to the handle
• On the outside, under the footrest, there is a folding mechanism for the seat (gure 40). Move
the grey slider and at the same time pull the lever (gure 41). Then lift the footrest up by
folding it as far as possible towards the part with the canopy (gure 47, 48, 49).
• Take the folded carrycot/seat and reposition it so that it is on the same side of the pushchair
as the handle (gure 50).
• In the centre of the frame, there is the mechanism responsible for folding the entire structure.
Move the grey slider and simultaneously pull the lever to activate it. Then lift the whole
pushchair using the handle to fold it (gure 44, 45).
• A pocket in the basket contains a strap to fasten the pushchair during transport. After
folding the pushchair, pull the strap through the frame of the pushchair and fasten it with a
snap (gure 46).
NOTE! Do not lift the buggy holding the mechanism enabling folding the buggy structure.
NOTE! If you are using stiening pads inside the gondola, remove them before folding the buggy
frame with the installed seat/carry cot.
Removing the canopy
• Unzip the zip around the canopy (gure 51).
• Slide the grey slider located at the canopy’s attachment to the pushchair frame, and then
slide the entire attachment up along the frame (gure 52).
• To reinstall the canopy follow the steps described above in the reverse order.
Removing the seat/carrycot cover
• Undo the two fasteners under the seat and undo the Velcro strap which fastens the cover
material to the frame (gure 53).
• Undo the two zips connecting the cover material to the seat/carrycot frame (gures 54, 55).
• To reinstall the cover follow the steps described above in the reverse order.
Removing the basket
• The basket is mounted to the frame by means of 8 Velcro straps and one snap. To remove the
basket, unfasten all Velcro straps and pull out the respective straps and unfasten the snap.
The locations of the above-mentioned xing points are shown in gures 56 to 61.
• To reinstall the basket follow the steps described above in the reverse order.
Installation of accessories
• Leg cover for the seat: To use the leg cover, put the pushchair in the sitting position, put the
cover on the footrest and fasten the 3 fasteners by hooking the special straps inside the
cover over the safety bar (gures 62 - 64).
• Mosquito net: In order to use the mosquito net, place the pushchair in the carrycot position
and unfold the canopy as far as possible. Pull the mosquito net over all edges of the open
carrycot and hook the fabric over the protruding elements at the canopy (gures 65-66).
• Rain cover: In order to use the rain cover, place the pushchair in the sitting position and
unfold the canopy as far as possible. Then place the rain cover loosely over the entire
pushchair (gure 67).
Installation and removal of the car seat
• Fit the additional adapters in the hooks of the frame of the pushchair (gure 68) and then
click the hooks of the seat into the adapters (gure 69).
WARNING! Car seat adapters are not included in the Nasjö pushchair set. They can be purchased
separately as an additional product from the skiddoü product range.