Skoda Fabia II 2009 User Manual

Workshop Manual
Fabia II 2007 ➤ , Fabia II 2009 ➤ ,
Fabia II 2011 ➤ , Octavia II 2004 ➤ ,
Octavia II 2010 ➤ , Octavia III 2013 ➤ ,
Octavia III 2014 ➤ , Rapid 2011 ➤ ,
Rapid India 2011 ➤ , Rapid NH 2013 ➤ ,
Rapid NH 2014 ➤ , Roomster 2006 ➤ ,
Superb II 2008 ➤ , Yeti 2010 ➤ ,
Yeti 2011 ➤
Gearbox 09G
Edition 07.2014
Service
Service Department. Technical Information
ProCarManuals.com

Skoda Fabia II 2009 Specifications

General

Brand	Skoda
Model	Fabia II 2009
Category	Automobile
Language	English

Summary

00 - Technical data

1 Identification of the gearbox

Provides information on gearbox identification, location, and specifications.

1.1 Location on the gearbox

Details the installation location of the automatic 6-speed gearbox 09G with 4-cylinder engines.

1.2 Identification characters, aggregate assignment, ratios

Lists identification characters, engine assignments, and gear ratios for various models.

1.2.1 Identification characters, aggregate assignment, ratios (Octavia II)

Specifies identification characters, engine assignments, and ratios for Octavia II.

1.2.2 Identification characters, aggregate assignment, ratios (Fabia II)

Specifies identification characters, engine assignments, and ratios for Fabia II.

1.3 Contents

Lists the table of contents for the technical data section.

32 - Torque converter

1 Torque converter

Details the torque converter and its related procedures.

1.1 Draining the torque converter

Instructions for draining the torque converter, including special tools.

1.2 Removing and installing gasket ring for torque converter

Procedure for removing and installing the torque converter gasket ring.

1.3 Checking the torque converter

Guidance on checking the torque converter for wear or damage.

1.4 Installing the torque converter

Steps for correctly installing the torque converter.

37 - Controls, housing

1 Electric and electronic components, fitting locations of the automatic gearbox

Overview of electric and electronic components and their locations in the automatic gearbox.

1.1 Summary of components - Electric and electronic components, fitting locations of the automatic gearbox

Summarizes electrical and electronic components and their fitting locations.

1.2 Removing and installing automatic gearbox control unit - J217-

Procedure for removing and installing the automatic gearbox control unit.

2 Repairing shift mechanism

Covers various aspects of repairing the shift mechanism.

2.1 Assembly overview - shift mechanism

Provides an assembly overview of the shift mechanism.

2.1.1 Summary of components - Gearshift mechanism -Octavia II up to 10.2009

Summarizes components for the Octavia II gearshift mechanism until 10.2009.

2.2 Inspecting the gearshift mechanism

Instructions for inspecting the gearshift mechanism for proper function.

2.3 Inspecting and adjusting the selector lever control cable

Guidance on inspecting and adjusting the selector lever control cable.

2.5 Removing and Installing the cover for the shift mechanism

Steps for removing and installing the cover of the shift mechanism.

2.5.1 Removing and Installing the cover for the shift mechanism - Fabia II and Roomster

Specific instructions for Fabia II and Roomster shift mechanism cover removal/installation.

2.9 Removing and installing selector mechanism

Procedure for removing and installing the selector mechanism.

2.9.1 Removing and installing shift mechanism Fabia II, Roomster, Rapid

Details for removing and installing the shift mechanism in Fabia II, Roomster, Rapid.

2.10 Removing and installing the selector lever control cable

Instructions for removing and installing the selector lever control cable.

2.12 Removing and installing selector lever lock solenoid - N110-

Procedure for removing and installing the selector lever lock solenoid.

2.12.1 Removing and installing selector lever lock solenoid - N110- for Octavia II, Octavia III, Superb II, Rapid and Yeti vehicles

Specifics for removing/installing the solenoid for Octavia II/III, Superb II, Rapid, Yeti.

2.14 Emergency release of gearshift mechanism out of position “P”

Steps for emergency release of the gearshift mechanism from 'P' position.

38 - Gears, control

1 Removing and installing oil pan, oil filter, slide valve body and internal wiring looms

Covers removal and installation of oil pan, filter, slide valve body, and wiring.

1.1 General Instructions

General guidelines for working with the gearbox, including safety warnings.

1.2 Summary of components - oil pan, oil strainer, slide valve body, internal wiring looms

Lists components related to the oil pan, strainer, slide valve body, and wiring.

1.4 Removing and installing oil pan

Detailed steps for removing and installing the oil pan.

1.5 Removing and installing the oil filter

Procedure for removing and installing the oil filter.

1.6 Removing and installing the slide valve body

Instructions for removing and installing the slide valve body.

39 - Final drive - differential

1 Replace the flange shaft gasket rings

Covers replacing flange shaft gasket rings with the gearbox installed.

1.1 Replacing the left flange shaft gasket ring

Specific steps for replacing the left flange shaft gasket ring.

1.2 Replacing the right flange shaft seal ring

Specific steps for replacing the right flange shaft seal ring.

2 Replacing the gasket ring for the gearshift shaft

Procedure for replacing the gasket ring on the gearshift shaft.

2.1 Replacing the gasket ring for the gearshift shaft

Detailed steps for replacing the gearshift shaft gasket ring.