Please read the operation mannual carefully and keep it properly before using the product.
Operation Mannual of Smartmi Standing Fan
2S
When your phone cannot connect with the fan, please press down the
and the buttons at the same time for 5 seconds
，
until you
hear the sound of “dididi” to reset the Wi-Fi.
Wi-Fi module resetting
Wi-Fi indicator status display
Blast up and down
Gentlely lift or press
the head or cover
of the fan to adjust
the blast orientation
upwards or downwards
Maintenance
Parts can be cleaned
The following parts can be cleaned with a soft cloth or sponge using
clear water or diluted neutral detergent.
Parts cannot be cleaned
The following parts should be slightly wiped with a soft and dry cloth.
5
Fan cover knob
11
Fan grille
12
Fan blade
13
Fan back cover
Do not flush the above parts with water.
Do not use diluents, light gasoline, detergents or alkaline detergents.
1
3
Motor + Support
Base
4
Cleaning of the fan
Make sure that the disassembling and cleanning of the fan are performed
after it stops working. Please completely dry the parts after cleaning and avoid
direct sunlight before installing and using them again.
Basic parameters
Manufacturer
：
Beijing Smartmi Electronic Technology Co., Ltd.
Address
：
11-1102, Office Building Rainbow City, NO.68 Qinghe Mid-Street, Haidian District, Beijing, P.R. China
190328-C
7
9
8 10
Fault clearance
On
Press the button to turn on the fan. Set the blast gear to1 when the
fan is first used and turned on.When the fan is turned on again, the blast
gear will default to the one it used last time.
Off
Long press the button for 2 seconds to stop the fan from working.
Application
Application
Function introduction
On/off and gear shift setting
Connected
Not connected Flashing light
Always on
Press the button to set whether or not to oscillate the fan.
The fan will automatically turn back to the right place after it is
turned off.
Oscillation control setting
Faults Fault reasons Solutions
The fan does not
work
Dead power outlet
Replace with a live
outlet
The power cord
is not attached in
place
Correctly attach the
power cord
The support and
base of the fan are
not installed in place.
Align the fan support
with the base socket,
and lock the connected
screws.
Cannot connect
to Wi-Fi
The channel of the
router is 5G.
Connect to the 2.4G
channel of the router.
Mobile APPs take up
too much memory.
Completely close and
restart the APP
The fan does not
connect to the
Internet for more
than half an hour.
Reset Wi-Fi
(Reset as per the Wi-Fi
module)
Fan blades block
and stop with
a long blast of
sound from the
fan for three
times and four
flashing status
indicator lights.
Fan blades are
blocked by foreign
matters.
Turn off the fan and take
out the foreign matters.
Motor fault
Contact the after-sales
personnel
Gear Off
1 2 3 4
Display
status
Press the button to change the fan speed. The blast will be switched
between1
、
2
、
3
、
4 while the corresponding status indicator light will
on with each press (see table below).
Status indicator light
Light offLight on
Product name Smartmi Standing Fan
2S
Nominal voltage 100V - 240V Power cord 1.5m
Model ZLBPLDS03ZM Nominal frequency 50/60Hz Battery type Lithium-ion battery pack
Gross weight approx.
4.9kg
Nominal power
25W
Rated capacity of
battery
2800mAh（33.6Wh）
Net weight approx.
3.5kg
Product size
340mm×330mm×960mm
Noise
≤60dB(A)
Wireless
connection
Wi-Fi IEEE 802.11 b/g/n
2.4GHz
Max. RF Output
Power
Wi-Fi 2.4G (2400-2483.5MHz): <20dBm
Fan blade knob
Upward
25°
Downward15
°
More Functions
You can use APP to switch on natrual breeze mode, set oscillating angle
and Timer setting.
Regulatory compliance information
Europe — EU declaration of conformity
We Beijing Smartmi electronic technology Co., ltd. hereby, declares that this equipment is in
compliance with the applicable directives and european norms, and amendments.
The full text of the EU declaration of conformity is available at the following internet address:
https://smartmi.com.cn/doc.html
Disposal and recycling information
Correct disposal of this product. This marking indicates that this product should not be disposal with other household
wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and
collection systems or contact the retailer where the product was purchased. They can take this product for environmental
safe recycling.
Installation
About “works with mijia”
“works with mijia” means the product can be controlled by mijia APP or
Xiao‘ai .Please note that “works with mijia” only acts as the verification
of the software. Xiaomi and mijia are not responsible for the production,
standards implementation, quality supervision and the like of the product.
End of the power cord
Attach the power/battery to charge
Attach the end of the power cord to the power interface at the back of
the base and then insert the plug to attach the power to charge.
The fan base can be used independently by pulling out the power cord
if the batteries inside the base are fully charged. Fan operation will
charge the battery fully instead of consuming it when the fan installed
with battery is connected to the power.
Connect with Mi Home / Xiaomi Home App
This product works with Mi Home / Xiaomi Home app*.
Control your device with Mi Home / Xiaomi Home app.
Scan the QR code to download and install the app. You will be directed
to the connection setup page if the app is installed already. Or search
"Mi Home / Xiaomi Home" in the app Store to download and install it.
Open Mi Home / Xiaomi Home app, tap "+" on the upper right, and then
follow prompts to add your device.
Note: The version of Mi Home app might have been updated, please follow the
instructions based on the current app version.
*The app is referred to as Xiaomi Home app in Europe (except for Russia). The name
of the app displayed on your device should be taken as the default.
To Next Page
Need help?
General
