Snap One Access Networks A750

To Next Page

snp1.co/arcc

A750 Access Point

Scan for Unleashed Set-Up Documentation

snp1.co/unleashed

Scan for ARCC Cloud-Based Controller

Set-Up Documentation

snp1.co/ARCC

snp1.co/unleashed

Technical Support

For All Partners:

Email: support-case@accessnetworks.com

For Snap One Partners:

Visit snp1.co/techsupport

Access Networks Partners:

Visit my.accessnetworks.com/partners/ and open a case.

Warranty and Other Legal Notices

Find the details of the product’s Limited Warranty on the

support tab for each Access Point model on

my.accessnetworks.com or snapav.com.

FIGURE 1 A750 Access Point: Top View

FIGURE 2 A750 AP Ports on Bottom Panel

Power

Supply

Operating

Characteristics

Max Power

Consumption

802.3af PoE

• 2.4GHz radio: 2x4,

19dBm per chain

• 5GHz radio: 2x4,

20dBm per chain

• 2nd Ethernet port,

on board IoT & USB

disabled

PoE: 12.54W

802.3at PoE+

• Full Functionality

• 2.4GHz radio: 4x4, 20

dBm per chain

• 5GHz radio: 4x4, 22

dBm per chain

• 2nd Ethernet Port,

on board IoT & USB

Enabled (3W)

PoE+: 22.34W

DC Power:

22.69W

TABLE 1 A750 Power

TABLE 2 A750 AP Ports

No. Label Description

2.5G ETH

PoE

100/1000/2500 Mbps PoE In Port:

RJ-45 Ethernet port (supports

802.3af/at PoE in)

2 1G ETH

10/100/1000 Mbps port: RJ-45

Ethernet port (non-PoE)

48V

0.75A

48V DC input

4 USB

USB Port

• Maximum Dimensions: 6 cm x

2 cm x 1.1 cm

• Interface: USB 2.0

• Connector: USB – Type-A plug

A750 Access Point

Published March 2023 Part Number 800-71927-202 Rev A

Page 1 of 3

Need help?

Do you have a question about the Snap One Access Networks A750 and is the answer not in the manual?

Overview

Function Description
Important Technical Specifications
Power Supply and Operating Characteristics (Table 1)
AP Ports (Table 2)
Optional Accessories (Table 3)
Usage Features
Mounting
Security
Network Management
Maintenance Features
Resetting to Factory Defaults
Technical Support
Warranty and Legal Notices
Compliance

The Access Networks A750 Access Point is a high-performance wireless access point designed for robust network connectivity. It supports both Unleashed and ARCC Cloud-Based Controller setups, offering flexibility in network management.

Function Description:

The A750 Access Point provides wireless network access, supporting various Wi-Fi standards and offering multiple power options. It is designed for both flat surface and drop-ceiling T-bar mounting, making it versatile for different installation environments. The device features multiple Ethernet ports, including a Power over Ethernet (PoE) input, and a USB port for additional connectivity. It can operate in different power modes, affecting its radio capabilities and the functionality of its secondary ports.

Important Technical Specifications:

Power Supply and Operating Characteristics (Table 1):

802.3af PoE:
- 2.4GHz radio: 2x4, 19dBm per chain
- 5GHz radio: 2x4, 20dBm per chain
- Secondary Ethernet port, on-board IoT & USB: Disabled
- Max Power Consumption: 12.54W
802.3at PoE+:
- Full Functionality
- 2.4GHz radio: 4x4, 20dBm per chain
- 5GHz radio: 4x4, 22dBm per chain
- Secondary Ethernet Port, on-board IoT & USB: Enabled (3W)
- Max Power Consumption: 22.34W
DC Power:
- Max Power Consumption: 22.69W

AP Ports (Table 2):

1 (2.5G ETH POE): 100/1000/2500 Mbps PoE In Port (RJ-45 Ethernet port, supports 802.3af/at PoE in).
2 (1G ETH): 10/100/1000 Mbps port (RJ-45 Ethernet port, non-PoE).
3 (48V 0.75A): 48V DC input.
4 (USB): USB Port (USB 2.0, Type-A plug).
- Maximum Dimensions: 6 cm x 2 cm x 1.1 cm.

Optional Accessories (Table 3):

902-1180-US00: Multi-Gigabit PoE injector (60W) (10/100/1000/2500/5000/10000 Mbps).
902-0180-US00: Gigabit PoE Injector (60W) (10/100/1000 Mbps).
902-1170-US00: Power Supply (48V, 0.75A, 36W).
902-0120-0000: Spare, Accessory Mounting Bracket.
902-0195-0000: Spare, T-bar ceiling mounting kit for mounting flush frame ceiling.

Usage Features:

Mounting:

Flat Surface Mounting:
1. Use the provided template to mark two drill holes.
2. Drill 4.75mm (3/16") holes approximately 25mm (1") deep.
3. Insert factory-supplied anchors and mounting screws, leaving about 6mm (1/4 inch) of the screw heads protruding.
4. Place the AP onto the mounting screws, aligning keyholes, and push down until the AP retainer tab snaps into place.
5. (Optional) Attach a customer-supplied padlock through the integral AP retainer tab for added security.
Drop-Ceiling T-Bar Mounting:
1. Position the T-bar bracket studs into the keyholes on the AP enclosure.
2. Slide the T-bar bracket until the AP retainer tab snaps into place, trapping the studs.
3. Insert the locking tab into the first position on the T-bar bracket.
4. Gently push ceiling tiles (if present) up and out of the way.
5. Position the T-bar bracket so its two clasps grip one edge of the T-bar.
6. Hold the AP in place and gently push the locking tab until its clasp grips the other edge of the T-bar, ensuring all three clasps are gripping.
7. (Optional) Attach a customer-supplied padlock through the bracket AP retainer tab for added security.

Security:

The A750 access point features an integrated security latch that locks the AP in position. An included key is used to disable the security latch for removal.

Network Management:

Supports both Unleashed and ARCC Cloud-Based Controller setups.
For configuration and management, refer to the Access Networks Partner Portal Resource Center.

Maintenance Features:

Resetting to Factory Defaults:

CAUTION: A reset button is available. Use the tip of a pen or a 3-mm flat-blade screwdriver to press and hold the reset button for 4 seconds or longer to restore factory defaults. This should only be done if instructed.
Post-Reset Access: After a reset, the internal AP web interface can be accessed via https://192.168.0.1. The device accessing it must use an IP address from 192.168.0.2 through 192.168.0.254, with a subnet mask of 255.255.255.0. The default username is super, and the password is sp-admin.

Technical Support:

For All Partners: Email support-case@accessnetworks.com.
For Snap One Partners: Visit snpl.co/techsupport.
Access Networks Partners: Visit my.accessnetworks.com/partners/ and open a case.

Warranty and Legal Notices:

Details of the product's Limited Warranty can be found on the support tab for each Access Point model on my.accessnetworks.com or snapav.com.

Compliance:

Wi-Fi Alliance, Wi-Fi, the Wi-Fi logo, Wi-Fi Certified, Wi-Fi CERTIFIED logo, Wi-Fi Protected Access, Wi-Fi Protected Setup logo, Wi-Fi Protected Setup, Wi-Fi Multimedia and WPA2 and WMM are trademarks or registered trademarks of Wi-Fi Alliance.