CUTTING DECKS, DEFLECTOR (28" & 33" Hi-Vac)
Footnotes:
TP 400-5003-5-RE-N
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
31
Part No Descri
tionItem Qt
Note
1 7073434 1 COVER, Spindle
2 7091015 2 SCREW, 1/4-20 x 3-1/2” Hex Head w/Free Spinning Washer
3 7091016 4 SCREW, 1/4-20 x 5/8” Hex Head w/Free Spinning Washer
4A 7061970 1 DECK, 28” Replacement (Painted deck w/decals & wheel
bracket fasteners)
4B 7061972 1 DECK, 33” Replacement (Painted deck with decals)
5 7090731 6 BOLT, 5/16-18 x 1/2” Short Neck Carriage, GR 5
6 7091070 8 NUT, 5/16-18 Hex Flange Lock, GR 5
7 7033570 1 BRACKET, Gage Wheel (Front)
8 7091532 3 SCREW, 3/8-24 x 3-3/4” Hex Head Cap, GR 5
9 7091518 3 NUT, 3/8-24 Hex Nyloc
10 7019190 3 WHEEL, Gage
11 7015272 3 SPACER
12 7033571 2 BRACKET, Gage Wheel (Rear)
13 7091508 2 BOLT, 5/16-18 x 3/4” Short Neck Carriage, GR 5 or 7090001
14 7016983 1 COVER, 28” Mulcher
14 7016984 1 COVER, 33” Mulcher
15 7026233 1 DEFLECTOR, Discharge, 28” & 33”
15A 7500484 1 ASSEMBLY, Discharge Deflector, 28” & 33” (without decal) Incl. items 15, 16, 18, 19, & 20
16 7026483 2 PUSH NUT, 1/4”
17 7091811 3 BOLT, 5/16-18 x 5/8” Hex Flange Lock, GR 5 or 7091811
18 7026234 1 PIN, Hinge
19 7016341 1 SPRING, Hinge
20 7033780 1 HINGE, Deflector (Deck side)
21 7091296 2 WASHER, 5/16” Flat
22 7013010 1 DECAL, Danger, (Cut Finger) or 7026831
23 7035635 1 BLADE, 28” Hat Shaped Hi-Lift standard equipment
23 7034168 1 BLADE, 33” Hat Shaped Hi-Lift standard equipment
24 7026453 1 BLADE, Ninja, 28”
24 7024741 1 BLADE, Ninja, 33”
25 7019515 1 BLADE, 28”
25 7019523 1 BLADE, 33”
26 7090492 2 NUT, 5/16-18 Wing
27 7091939 2 NUT, 1/2-20 Hex, GR 5 or B was 7090559, Hex Jam Nut
28 7090509 2 WASHER, 1/2” Internal Tooth Lock
29 7090613 9 NUT, 3/8-16 Hex Flange Lock
30 7090612 3 BOLT, 3/8-16 x 3/4” Hex Flange Lock
31 7090491 2 SCREW, 1/2-20 x 1-1/4” Hex Head Cap, GR 5 was 7090392
To Next Page
Loading...
Need help?
General
