How to reset the fault LED on Motorisation module of Socomec Industrial Electrical?
To reset a fault condition on the motorisation module, switch the ATyS p from AUT to Manu and back to AUT. Note that the FAULT / Manual LED will also be on when contact 313 is closed with 317, so force the ATyS to off position. If the Fault LED remains on abnormally, contact SOCOMEC.
What does the message F13 ROT-1 or F23 ROT-2 mean on Socomec Industrial Electrical?
If your product displays the message F13 ROT-1 or F23 ROT-2, check for phase rotation consistency (or conventional direction) between the source and parameter ROT in the SETUP menu, or between the two sources.
What to check if return to priority source 1 has been executed, but source 2 is still running on Socomec Industrial Electrical (M-G application)?
If return to priority source 1 has been executed, but source 2 is still running (M-G application), make sure that: * CDT (Cool Down Timer) has counted down. The display indicates CDT xxx SEC after switchover to the priority source. * The status of the "gen set start" contact (contact 71 – 72 - 74) Check that the contact changes state after timedelay CDT has counted down. * The product is not in MAN, CONTROL or INH mode. In this case Manual or Control LMED would be On.
Why is it impossible to padlock Socomec Industrial Electrical?
If it's impossible to padlock, verify: * That the front selector switch is in manual position. * That the emergency handle for manual operation is not inserted into the ATyS manual slot. * That the ATyS is in 0 position (Padlocking is only possible in 0 position for standard products).
Why can't the ON LOAD and OFF LOAD tests be started via the keypad on Socomec Industrial Electrical?
If the ON LOAD and OFF LOAD tests cannot be started via the keypad, you should check: * That the mode selector switch is set to AUT and that the AUT LED is illuminated. * The operating mode password (factory code 0000) to access the test functions. * That the ON LOAD TEST or OFF LOAD TEST LEDs are illuminated, according to the selected test mode. * That the product is set to application type M-G. * That there is no mains loss when starting the test. The SOURCE LED (priority side) should be illuminated. * The status of the "gen set start" contact (contact 71-72-74).
What to do if the Socomec Industrial Electrical product does not switch over after the priority source is lost?
If the product doesn't switch over after the priority source is lost, check the following: * Back-up source availability. * Back-up source voltage and frequency thresholds and hystereses and modify if required. * That the product selector switch is in AUTO. * That automatic operation has not been inhibited by external orders. * Priority source voltage and frequency thresholds and hystereses and modify if necessary. * That the time-delay 1RT (Source 1 Return Timer) has counted down, and that it is not too long. (The display indicates 1RT xxxSEC). * That the "manual retransfer" function is not activated. If this function is unnecessary: In the SETUP menu, the RETRANS variable must be at NO. * That automatic operation has not been inhibited by external orders. * That the IN...
General| Product Category | Transfer Switch |
|---|---|
| Protection Degree | IP20 |
| Operating Mode | Manual |
| Electrical Durability | 1, 000 cycles |
| Control Voltage | 24 V DC |
Provides step-by-step instructions for the initial setup of ATyS p models from Frame B3 to B5.
Details the initial setup process for ATyS p models from Frame B6 to B8.
Details the interface of the ATS control module, including LEDs, LCD, and keypad.
Covers the environmental requirements, including IP rating, operating conditions, and storage.
Lists and briefly describes the accessories available for the ATyS p product.
Provides detailed dimensional specifications for different ATyS p frames (B3 to B8).
Explains the recommended and allowed mounting orientations for the ATyS p.
Details the process for assembling various customer-mounted accessories for the ATyS p.
Covers the power connection aspects, including cable/bar connections and cross-sections.
Explains different network types and their corresponding connection possibilities.
Details the wiring and connections for control circuits, including typical diagrams.
Explains the voltage sensing and power supply kit installation and standard configuration.
Describes manual operation, including emergency manual operation and padlocking.
Explains electrical operation, including dual power supply and voltage sensing inputs.
Details how to program the ATyS p using the Easy Config software.
Explains how to program the ATyS p using its built-in keypad.
Describes how to navigate and visualize information on the LCD display.
Explains how to interpret event messages displayed on the LCD screen for troubleshooting.
General guidance on keypad programming, including navigation and password entry.
Details the timer settings for various operational sequences and delays.
Explains the Input/Output menu for configuring and managing inputs and outputs.
Details the internal and external programmable inputs available for the ATyS p.
Lists and defines the available programmable outputs for the ATyS p.
Details the communication settings menu for configuring network parameters.
Provides MODBUS addresses for setting various timers.
Details MODBUS addresses for setting upstream voltage thresholds.
Explains MODBUS settings for user-defined power thresholds.
Provides MODBUS addresses for network setup parameters.
Details MODBUS addresses for setting up inputs and outputs.
To Next Page
