SolarEdge Home Battery 400V - User Manual

What’s in the Package
Quick Installation
Guide
Version 1.1
SolarEdge
Home Battery 400V
for use with SolarEdge Inverters
North America
© SolarEdge Technologies, Ltd.
All rights reserved.
Version: 1.1, January 2025
Subject to change without notice.
SolarEdge Home
Battery
Mounting bracket
Decorative cover
Required Personnel and Tools
x 2
Cover
screws
Dolly with lift
and ratchet straps
Drill
min 2
Mounting
screws -
m ax M10
Min 2 qualified
installers
MC 4 crimper
8/ 10/12 AWG
Level
Handles (available
from SolarEdge)
x 4
DC cable
600V insulated
x 2
Branch connectors
( optional, available
from SolarEdge)
T orque
wrench
Phillips
screwdriver
x 2
Mounting
bracket screws
MC 4
connectors
Support Contact Information
In case of any technical issues with SolarEdge
products, please contact us at:
https://www.solaredge.com/service/support
Conduit
holder
SolarEdge
Home Network
plug-in (available
from SolarEdge)
2
3
Hang battery on
mounting bracket
1. Lift the battery to the height of the mounting bracket.
2. Hang the battery on the mounting bracket, while
holding it by the handles.
3. Secure with a mounting bracket screw (supplied) on
each side. Apply a torque of 42lbf·in.
1
2
4
Prepare cables
1. Mount the conduit holder.
2. Pass the DC cables and grounding cable through the
conduit holder at the bottom of the battery.
3. Connect the grounding cable to the grounding
terminal with a torque of 66 in*lbs/7.5 N*m.
4. Crimp the DC cables to the MC4 connectors
(supplied) and tighten the MC4 connector glands
with a torque of 30lbf·in
3
1
Connect to inverter
1. Make sure the inverter is OFF.
2. Connect the DC cables to the DC+ and DC- inputs.
Observe correct polarity.
3. Install the SolarEdge
Home Network plug-in and antenna
in the inverter. See the Installation
guide
4. Connect cables to the inverter.
See the Connection
and Configuration
application
note.
5. For multiple SolarEdge Home Batteries
connection, see Connecting
the Home
Hub
Inverter to multiple Home Batteries
+
-
2
3
Home Network
4
1
OFF
The SolarEdge Home Battery 400V can be added to your SolarEdge All-in-One residential system. This battery is
intended for storing excess solar production and delivering backup power.
WARNING!
This symbol on the product or in the accompanying documentation denotes a hazard. It calls attention to a procedure
that, if not correctly performed or adhered to, could result in injury or loss of life. Do not proceed beyond a warning
note until the indicated conditions are fully understood and met.
WARNING!
Before installing or operating the SolarEdge Home Battery (referred to as the “ Battery ” ), read the Safety and Handling
instructions at the back of this page.
Install mounting bracket
When selecting the installation location:
• Maintain a clearance of min 8 ” from other
objects.
• Make sure the max distance from the inverter is max
164ft.
Make sure the installation surface sustains the weight
of the battery (267lb).
1. Level the bracket.
2. Mark two drilling spots.
Use either the inner or outer pair of holes.
If necessary, you can use the additional holes to secure
the bracket.
3. Drill holes in the installation surface.
4. Install the mounting bracket and secure with screws.
16 ”
24 ”
2
3
4
1
1
m in 8 ”
m ax 164 ft
Transport battery
2. Place the battery upright on a dolly and secure it with
straps.
Caution!
Stand the battery on the rubber protector only!
3. Transport the battery to the installation location.
1
2
3
CAUTION!
1. Screw in all FOUR handles to the battery frame.
Make sure to screw in the handles all the way.
Do not use a bent, cracked, or otherwise damaged
handle.
Long-nose
pliers
2
3
4
5
I
P 0
2 sec
1 ON
2
Power on and associate
6
For the SolarEdge Home Battery - Emergency
Response guide, including emergency phone
numbers, see:
https://www.solaredge.com/sites/default/files
se-
energy-bank-emergency-response-guide.pdf
1. To power on and operate the battery, turn on the DC
circuit breaker, and set the P/1/0 switch to
“ 1 ” (ON).
2. To associate with the inverter, hold the battery ’ s
P/1/0 switch to
P for 2 seconds and then release.
NOTE!
To power OFF the battery, follow these steps:
1. Set the P/1/0 switch to “ 0 ” (OFF).
2. Turn off the DC circuit breaker.
IMPORTANT NOTE!
If the inverter is turned off or in fault state, make sure to
turn off the battery to maintain its lifetime.

SolarEdge Home Battery 400V Specifications