Need help?Do you have a question about the SOMMER duo vision 500 and is the answer not in the manual?
General| Manufacturer | SOMMER |
|---|---|
| Product Name | duo vision 500 |
| Power Supply | 230 V AC |
| Max Door Area | 8 m² |
| Frequency | 50 Hz |
| Radio Frequency | 868.8 MHz |
| Protection Class | IP20 |
| Max. pulling force | 500 N |
| Motor type | DC motor |
| Voltage | 230 V |
| Remote Control | Yes |
| Battery Backup | Optional |
| Speed | 0.2 m/s |
| Safety Features | Automatic obstacle detection |
Explains symbols used in the manual.
General safety guidelines for installation and operation.
Instructions for storing the drive unit.
Key operational safety points and precautions.
Safety advice for using radio remote controls.
Location and information on the type plate.
Defines the proper and improper uses of the drive.
Table of maximum door dimensions for different models.
Specifications and technical details of the drive.
Statement of compliance with EU directives.
Lists the components included in the package.
Manufacturer's declaration for installation of an incomplete machine.
Crucial safety warnings for installation.
Recommended protective gear for installation.
Guidance on installing safety features.
List of tools needed for installation.
Safety precautions during the installation process.
Overview of door types and required accessories.
Practical advice for a smooth installation.
Instructions for setting up the emergency release.
Specific considerations for swinging doors.
Specific wiring advice for these door types.
Guidance on choosing the correct installation method (A, B, C).
Procedure for adjusting the top roll.
Steps for preparing installation variants A and C.
Steps for preparing installation variant B.
Detailed example of installing variant B.
Instructions for mounting the drive on header or ceiling.
Steps for marking and drilling for mounting.
Steps for attaching the drive and header fitting.
Ensuring the drive is parallel to door rails.
Steps for aligning and securing the drive.
Connecting the push rod to the door bracket.
Securing the C-rails vertically.
Instructions for mounting the controller housing.
Choosing between installation variants A/B.
Specific installation steps for variants A and B.
Specific installation steps for variant C.
Steps to install and connect the circuit board.
Guidance on installing the electrical wall socket.
How to connect an external button.
Connecting potential-free key switches.
Crucial safety points for initial operation.
How to set the door's open and close limits.
Steps to program the drive's automatic force setting.
Steps to program the remote control.
How to clear stored remote control codes.
How to test the emergency release function.
How to verify force settings.
Attaching the information sign for emergency release.
Placement of warning signs.
Important safety rules during operation.
How to open the door using buttons or remote.
How to close the door using buttons or remote.
Explanation of door movement sequences based on DIP switch 7.
Detailed explanation and usage of emergency release.
How to perform a control unit reset.
How an intermediate stop affects drive movement.
Behavior during power failure.
Behavior when safety input is triggered.
How overload protection works.
How the drive behaves after power restoration.
Information about HomeLink compatibility and safety.
Explanation of the control board's LEDs and buttons.
Detailed steps for programming remote controls.
How to exit programming mode.
Removing specific remote buttons.
Removing an entire channel.
Clearing all stored codes.
How to connect an external antenna for better reception.
Explains the function of button 2.
Default DIP switch settings and cable lengths.
How DIP switches affect obstacle detection.
How the drive reacts to obstacles when opening.
How the drive reacts to obstacles when closing.
Wiring and function of photo eyes.
Connecting an auxiliary button.
Connecting and function of a warning light.
Wiring for the primary button connection.
Setting the prewarning time for lights.
Functionality and benefits of the Backjump feature.
How DIP 7 controls opening and closing actions.
Setting up partial door opening.
Using two buttons for partial opening.
Remote control operation for partial opening.
Connecting an external antenna.
Reference to TorMinal owner's manual.
Explanation of carriage circuit board terminals.
General safety and cleaning advice.
Instructions for cleaning drive components.
Steps to replace the drive's light bulb.
How to replace the fuse for the warning light.
Schedule and procedures for testing safety devices.
Instructions for disassembling the drive.
Guidelines for proper disposal of the unit.
Information on warranty and support.
General advice for resolving issues.
Troubleshooting for blinking lights.
Troubleshooting for non-functional drive and lights.
Troubleshooting for missing lights during operation.
Troubleshooting for a non-functional drive.
Troubleshooting remote control operation.
Troubleshooting button operation.
Troubleshooting for closing reversal.
Troubleshooting for opening reversal.
Troubleshooting for stopping during opening.
Troubleshooting for failure to close.
Troubleshooting unresponsive commands.
Troubleshooting unresponsive commands after closing.
Troubleshooting for a non-functional warning light.
Troubleshooting inconsistent door speed.
Troubleshooting learning procedure failures.
Troubleshooting radio receiver LED status.
Troubleshooting continuous LED illumination.
Troubleshooting LED illumination.
To Next Page