Need help?Do you have a question about the Sonic Safety HG-1500 and is the answer not in the manual?
General| Frequency | - 303 / 433Mhz |
|---|---|
| RF Range | - 50 Metres in open space |
| Dialing Type | - Pulse/ Tone selectable |
| Preset Telephone Numbers | - 6 phone numbers, 20 digits for each number |
| Power Source | - 240V DC12V 1000mA adapter |
| Power Consumption | - 70mA (idle), 300mA (activated) |
| Wired Input Trigger | - Burglary : NC (normal close) /1 - Smoke : NC (normal close) /1 - Help : NC (normal close) /1 |
| Wired Output Trigger | - No output voltage: NC(normal close) /1 (DC 5V, 100mA) |
| Impedance | - 200 ms up, 300 O below |
| Voice Message Playing Time | -Total 30 seconds, Each voice message is 15 seconds |
| Back-up Battery (Optional) | - Approximate 8 hours ( NO AC adaptor) |
| Temperature Range | - 5°C ∼ +50°C |
| Security Code | - Hopping code |
| Alarm Activation Time | - 1∼255 seconds (available alarm time setting) |
| Material | - ABS |
Weight and Dimensions| Weight | - 850 g |
|---|---|
| Dimensions | - 26 cm X 17 cm X 6 cm |
Adherence to operating instructions, proper power and cord handling, cleaning, and avoiding liquids.
Procedures for handling damaged equipment and routine system maintenance.
Actions to take upon returning to a premises with an active alarm.
Lists the main components included in the system.
Lists additional accessories available for the system.
Illustrates the typical setup and placement of system components.
Guidance on selecting an optimal central area for the Main Console.
Information on learning sensors into the Main Console for zone configuration.
Instructions for installing the backup battery in the Main Console.
Steps to connect the AC adapter and power on the Main Console.
Procedure for connecting the Main Console to a telephone line.
Instructions to extend the antenna for maximum communication range.
Steps for setting up the console on a table or wall.
Information on the two sets of passwords for system settings.
Visual guide and explanation of the Main Console's LCD panel and buttons.
Illustration and description of each terminal block connection point and its purpose.
Steps to enter the default installer password (123456).
Information on error handling, keyboard locking, and system lockout.
Accessing the main setting menu by pressing '0'.
Setting exit, alarm, and entry delay times (0-T).
Programming up to six phone numbers for auto-dialing (123456-P).
Recording up to four segments of voice messages for alerts (7-MSG).
Setting the auto-dialing behavior (single or all numbers) (8-DIAL).
Instructions for changing Install and Master passwords (9-CODE).
Entering the sequential mode to learn sensors into the system.
Procedures for learning various sensor types (PIR, Door/Window, etc.).
Replacing faulty sensors by re-learning them.
Options to clear single or all learned sensors.
Entering the default master password (135246) to access settings.
How to arm the system in Away and Home modes.
Reviewing installed memory data without changing it.
How to trigger panic alerts and control the system via telephone.
Reviewing specific settings like exit time, phone numbers, dial mode.
Using voice communication and activating door sensor chimes.
System's auto-dialing process and LCD warning indicators.
Instructions to enable or disable the audible alarm sound.
How to reset the system to factory default settings.
Description of the PIR sensor's LED, switches, and sensitivity.
Procedure for replacing the battery in the PIR motion detector.
Setting zone address and guidelines for optimal PIR sensor placement.
Steps and considerations for mounting the PIR sensor.
Securing the mounting bracket to the wall.
Placing the PIR sensor and testing its functionality.
Details on components, LEDs, and battery replacement for sensors.
Setting sensor type and understanding console display messages.
Configuring the sensor type (door/window) and its zone address.
Important notes on sensor operation and proper gap between sensor and magnet.
Detailed steps for installing the HG-122 sensor.
Detailed steps for installing the HG-123 sensor.
Description of components, learning process, and basic operation.
How to arm, disarm, and trigger the alarm using the remote.
Description of the optional accessory and connection instructions.
Display messages for different types of triggered wire sensors.
Frequency, power, consumption, RF range, and security code details.
Alarm activation time, dialing, voice message, temperature, and material specs.
Record for install code, master code, and timing parameters.
Record for preset telephone numbers for emergency calls.
Form to log sensor learn number, install place, position, and comment.
Flowchart for arming modes and settings like ID/Central codes.
Flowchart of installer options and detailed setting breakdowns.
Flowchart for accessing and reviewing system settings.
To Next Page