Sony Cyber-shot DSC-RX100M3 - Page 21

DSC-RX100M3/RX100M3G_L2
2-4
2-1. EXPLODED VIEWS
2-1-1. OVERALL SECTION
ns : not supplied
Ref. No. Part No. Description
Ref. No. Part No. Description
1 4-528-653-01 BOTTOM, CABINET
2 4-534-041-01 COVER, EDGE
3 4-467-782-01 LID (710), USB
4 4-528-652-01 LID, HDMI
5 1-490-435-21 SWITCH BLOCK, CONTROL (SW60600)
6 X-2588-293-2 CABINET (REAR) ASSY
7 4-433-887-02 SHEET (PAD) (500), ADHESIVE
8 4-433-888-01 PAD (500)
9 4-528-645-01 PLATE, USB
10 4-528-646-01 PLATE, HDMI
11 4-471-755-01 INSULATING SHEET (MF-LC (710))
12 4-544-873-01 SPACER, LC BACK
#196 4-178-124-01 SPECIAL (M1.4 (D2.75)) (Note)
#247 4-412-769-11 SCREW (M1.4), NEW TRU-STAR, P2 (Note)
1. Remove in numerical order (1 to 5) in the left figure.
DISASSEMBLY
Screw
#196: M1.4 X 2.0
(Black)
4-178-124-01:
2.0
1.4
#247: M1.4 X 2.5
(Black)
4-412-769-11
2.5
1.4
1 #247 X 5 → Open the battery lid (1)
Bottom View
#247
Front View
1
2 Tilt the LCD (2) → #196 X 2 → #247 X 4
Back View Left ViewRight View Left View
Displace the
Cabinet (Rear)
Assy
#196
#247 #247
2
1 Tilt the LCD.
Remove the Cabinet (Rear) Assy
to the position shown in the figure.
2
A
4
Remove Cabinet (Rear) Assy
while turning it.
USB Lid
HDMI Lid
3
Tweezers
While lifting the A portion of
the USB Lid and HDMI Lid
slightly with tweezers or the
like, pull the USB Lid and
HDMI Lid in the direction of
arrow to disengage it.
3
DISCHARGING OF THE CHARGING CAPACITOR
ストロボ用充電コンデンサの放電
5 #247 X 2
Back View Left View
#247
#247
#247
(Note)
A
A
1
3
1
2
2 6
Main Board Section
(See page 2-5)
4
5
This screw is used to secure the hinge block
section, but remove it to detach the cabinet (rear)
assy during disassembly.
In the assembly process, however, do not install
this screw to attach the cabinet (rear) assy, but
tighten this screw to secure the hinge block
section.
Claw
Claw
#247
(Note)
#247
(Note)
#247
(Note)
#247
(Note)
#196
(Note)
Claws
Claws
8
7
3
4
12
11
9
10
ns
1
5 Hinge Block Section
(See page 2-10)
2
Note
Note: This screw cannot be reused. Discard the screw removed once
in servicing. Instead, use a new screw.
Note:
 このねじは再利用することができません。サービス対応時に一
度でも外した場合は新品のねじと交換してください。
Ver. 1.1 2015.01
SYSSET
2018/10/1703:17:13(GMT+09:00)