Sony Cyber-shot DSC-RX100M3 - Lens Block Section

DSC-RX100M3/RX100M3G_L2
2-11
2-1-8. LENS BLOCK SECTION
ns : not supplied
Ref. No. Part No. Description
Ref. No. Part No. Description
351 A-2057-540-A SERVICE, LENS DEVICE LSV-1710A (Note 1, 2)
352 A-2080-831-A RING (A) (SERVICE), ORNAMENTAL
353 4-531-005-01 TAPE, BARRIER (Note 3)
354 A-2032-894-A BARRIER BLOCK ASSY
355 4-294-347-01 RETAINER, FG
356 A-2049-433-A DC MOTOR WORM ASSY
357 A-2032-915-A LUBRICATING BLOCK ASSY, WHEEL
358 A-1940-536-A GEAR A LUBRICATED ASSY
359 A-2032-916-A LUBRICATING BLOCK ASSY, (B)
360 Selection Parts SPACER PLATE
361 A-2057-541-A INDIVIDUAL, FILTER BLOCK ASSY (including CP001
(CMOS imager) and CD-847 flexible board) (Note 4, 5, 6)
362 4-573-348-01 INSULATING SHEET (ST3) (609) (Note 7)
363 A-2009-287-A LF-2091 FLEXIBLE BOARD, COMPLETE
#176 3-947-504-31 SCREW (M1.2)
#258 4-299-468-11 SCREW, TAPPING UB1.2 (CH)
#302 3-703-816-18 SCREW (M1.4X3.5), SPECIAL HEAD
(Claws)
(Claws)
(Claw)
#176
#302
#258
#258
(Note 1, 2)
(Note 3)
355
356
359
351
360
358
354
353
352
357
(including CP001
(CMOS imager) and
CD-847 flexible board)
(Note 4, 5, 6)
361
362
ns
363
ns
ns
ns
ns
ns
ns
(Note 7)
1. The meaning of the symbol in left figure is as follows. Be careful when you remove it.
◇-X: Solder
DISASSEMBLY
Screw
#176: M1.2 X 2.0
(Silver)
3-947-504-31
2.0
1.2
#258: M1.2 X 3.5 (Tapping)
(Silver)
4-299-468-11
1.2
3.5
#302: M1.4 X 3.5
3.5
1.4
(Silver)
3-703-816-18
Note
Note 3: Do not reuse the Barrier Tapes because its adhesive force
decreases when it is removed once.
Note 3:
 Barrier Tapeは一度剥がすと粘着力が弱くなるため，再利用は
しないでください。
Note 2: Refer to the following each item when you exchange parts of
Lens Block.
• 1-9. ORNAMENTAL RING (A) OR BARRIER BLOCK ASSY
REPLACING METHOD (page 1-9)
• 1-10. 1 GROUP FRAME BLOCK ASSY REPLACING
METHOD (page 1-9)
Note 2:
 レンズブロックの各部品を交換する際は，下記の各項目を参照
してください。
・ 1-9. ORNAMENTAL RING (A) OR BARRIER BLOCK
ASSY REPLACING METHOD (page 1-9)
・ 1-10. 1 GROUP FRAME BLOCK ASSY REPLACING
METHOD (page 1-9)
Note 4: When this part is removed, adjustment is required.
 For the adjustment method, refer to “Adjustment items after
replacing parts” in the Note tab of the Adjust manual.
Note 4:
 この部品を取り外したときは調整が必要です。
 調整方法についてはAdjust manualのNoteタブにある
Adjustment items after replacing partsを参照してください。
Note 1:
Hold the Lens Block at the
center of both sides.
Do not hold the following part.
Hold here.
NOTES ON HOLDING THE LENS BLOCK
Lens barrier
*Very weak
Zoom motor,
Gear B
*Very weak
G10 lens
*Very weak
Note 5: Refer to “1-3. NOTES ON REMOVING/INSTALLING THE
IMAGER BOARD (CD-847 FLEXIBLE BOARD)”.
Note 5:
“1-3. イメージャ基板 (CD-847フレキシブル基板) の取り外し／
取り付け時の注意” を参照してください。
Note 6: Be sure to read “Precautions for Replacement of Imager” on
page 6-1 of Level 3 when changing the imager.
Note 6:
 イメージャの交換時はLevel 3の6-1ページ，“イメージャ交換
時の注意” を必ずお読みください。
The changed portions from
Ver. 1.2 are shown in blue.
Ver. 1.3 2016.11
Note 7:
NOTES ON INSTALLING THE INSULATING SHEET (ST3) (609)
That it does not overlap on the rib.
Reference 1 (vertical walls):
The inside is less than 1mm.
Reference 2 (vertical walls):
The right and left is less than 1mm.
Paste it to the edge of the sheet.
INSULATING SHEET (ST3) (609)
SYSSET
2018/10/1703:17:13(GMT+09:00)