5-10
1-2-2. Initializing the B, E, F Page Data
1. Initializing the B, E, F Page Data
Note: If the B, E, F Page data has been initialized, “Modification of B, E,
F Page Data” and following adjustments need to be performed again.
1) Modification of B, E, F page data
2) Video system adjustments
3) Camera system adjustments
Adjusting page F
Adjusting Address 10 to FF
Adjusting page E
Adjusting Address 00 to FF
Adjusting page B
Adjusting Address 00 to FF
Initializing Method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 6, address: 00, and set data: 2D.
3) Select page: 6, address: 01, set data: 2D, and press the PAUSE
button of the adjustment remote commander.
4) Select page: 6, address: 02, and check that the data changes to
“01”.
5) Perform “Modification of B, E, F Page Data”.
2. Modification of B, E, F Page Data
If the B, E, F Page data has been initialized, change the data of the
“Fixed data-2” address shown in the following tables by manual
input.
Modifying Method:
1) Before changing the data, select page: 0, address: 01, and set
data: 01.
2) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
Note: If copy the data built in the different model, the camcorder may
not operate.
3) When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
4) Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
Processing after Completing Modification of B, E, F Page data
1) Select page: 2, address: 00, and set data: 29.
2) Select page: 2, address: 01, and set data: 29, and press the
PAUSE button of the adjustment remote commander.
3. F Page table
Note: Fixed data-1 : Initialized data. (Refer to “1. Initializing the B, E, F
Page Data”.)
Fixed data-2 : Modified data. (Refer to “2. Modification of B, E, F
Page Data”.)
Address
Remark
00 to 0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F
40
41
10
00
10
01
11
00
00
00
00
00
00
00
20
20
00
40
0A
00
A8
85
5C
4E
49
45
7A
77
14
78
2F
37
40
D0
B5
43
03
Fixed data-1
(Initialized data)
Flange back adj.
Light level adj.
Fixed data-1
Light level adj.
F No. standard data input
Fixed data-1
HALL adj.
Fixed data-1
(Initialized data)
HALL adj.
Fixed data-1
(Initialized data)
AWB standard data input
Fixed data-1
Auto white balance adj.
Color reproduction adj.
Initial value
NTSC PA L
10
00
10
01
11
00
00
00
00
00
00
00
20
20
00
40
0A
00
A8
85
5C
4E
49
45
7A
77
14
78
2F
37
40
D0
B5
43
03
Downloaded from: https://www.usersmanualguide.com/
To Next Page
Loading...
