6-4
8. Audio
(8-2) ARP → 1930
Error14 : ARP → 1930 video NG
15 : ARP → 1930 audio NG
(8-3) Test Tone
A pink noise signal is output from the AVD (IC401) through
optical coaxial digital terminal and analog audio terminal.
Error: Not detected.
For DVP-S330 (2ch models):
All channels → 2ch Left → 2ch Right are checked in this
order.
For DVP-S525D/DVP-S725D
(DD models):
All channels → 2ch Left → 2ch Right → Front Left →
Front Right → Rear Left → Rear Right → Center → Sub
Woofer are checked in this order.
Caution: Sub Woofer is checked only for low-frequency
components, and no sound will be heard unless a
proper super woofer is connected.
Check Items List
2) Version
(2-2) Revision
(2-3) ROM Check Sum
(2-4) Model Type
(2-5) Region
3) Peripheral
(3-2) Gate Array Check
(3-3) EEPROM Check
(3-4) NAND Flash Check
(DVP-S725D)
4) Servo
(4-2) Servo DSP Check
(4-3) DSP Driver Test
5) Supply
(5-2) ARP Register Check
(5-3) ARP to RAM Data Bus
(5-4) ARP to RAM Address Bus
(5-5) ARP RAM Check
6) AV Decoder
(6-2) 1930 RAM
(6-3) 1930 SP
7) Video
(7-2) Color Bar
(7-3) Composite Out (DVP-S325/DVP-S525D (except for Aus-
tralian model)/DVP-S725D (except for Australian model))
(7-4) Y/C Out (DVP-S325/DVP-S525D (except for Australian
model)/DVP-S725D (except for Australian model))
(7-5) RGB Out (DVP-S325/DVP-S525D (except for Australian
model)/DVP-S725D (except for Australian model))
(7-6) Component Out (DVP-S325/DVP-S525D (except for Aus-
tralian model)/DVP-S725D (except for Australian model))
8) Audio
(8-2) ARP → 1930
(8-3) Test Tone
Error Codes List
00: Error not detected
01: RAM write/read data discord
02: Gate array NG
03: EEPROM NG
04: Flash memory clear error
05: Flash memory write error
06: Flash memory read data discord
08: ARP register read data discord
09: ARP ←→ RAM data bus error
10: ARP ←→ RAM address bus error
11: ARP RAM read data discord
12: Servo DSP NG
13: 1930 SDRAM NG
14: ARP → 1930 video NG
15: ARP → 1930 audio NG
16: 1910 UCODE download NG
17: System call error (function not supported)
18: System call error (parameter error)
19: System call error (illegal ID number)
20: System call error (time out)
21: NAND Flash faulty blocks exceed 10
90: Error occurred
91: User verification NG
92: Diagnosis cancelled
(7-6) Component Out
EURO-AV Component video output check
This check is executed only for European models DVP-
S325/DVP-S525D (except for Australian model)/DVP-
S725D (except for Australian model).
AVD color bar command write → Video (EURO-AV Com-
ponent) OUT
Error: Not detected.
With the Component of video output turned on, the color
bar signals are output from the EURO-AV terminal.
(7-7) Euro AV Through
Euro-AV2 input check.
This check is executed only for European models DVP-
S325/DVP-S525 (except for Australian model) /DVP-
S725D (except for Australian model).
Check video and audio signal pass through from Euro-AV2
to Euro-AV1.
Error: Not detected.
To Next Page
Loading...
