Sony MVS-8000X SystemMVS-7000X System - Page 176

USO RESTRITO
176
Wipe Settings for Independent Key Transitions
Knob
Parameter
Adjustment
Setting values
1
Angle
Angle of pattern
rotation at start
of transition
–100.00 to
+100.00
a)
Chapter
5
Wipes
To set the wipe position using the trackball or
joystick
You can also set the wipe position using the trackball or
joystick in the device control block.
1 In the device control block, press the [M/E1], [M/E2],
[M/E3], [M/E4], [M/E5], or [P/P] button, turning it on.
Notes
To select [M/E4] or [M/E5], a previous button
assignment in the Setup menu is required (see page
396).
The buttons in the device control block are assigned to
the wipe position setting as follows.
Table 1: Buttons and assigned settings
Button name
Setting
K1 CB1
Wipe position for independent key 1
transition
K2 CB2
Wipe position for independent key 2
transition
K3
Wipe position for independent key 3
transition
K4
Wipe position for independent key 4
transition
Table 2: Buttons assigned to functions
Button name
Function
POS
Toggle Position on or off.
X, Y
Fix the operating direction.
CTR
Return the pattern position to the
center of the screen.
2 Press one of the buttons in Table 1 above, to select the
wipe position to which the operation applies. Multiple
selections are supported.
Notes
By setting the operation mode in setup, you can also
use [K1 CB1], [K2 CB2], [K3], and [K4] to select keys
5 to 8. In this case, press [SHIFT], turning it on, then
press [K1 CB1], [K2 CB2], [K3], or [K4] to select one
of keys 5 to 8. However, it is not possible to select
more than one key.
For details of assignment for keys 5 to 8, see
“Assigning Buttons for Selection of Keys 5 to 8 in the
Setup Menu” in the Appendix (page 397).
3 Press the [POS] button, turning Position on.
4 Move the trackball or joystick, to set the wipe position.
By pressing the [X] button, turning it on, you can
restrict movement to the horizontal direction, and by
pressing the [Y] button, turning it on, you can restrict
movement to the vertical direction.
To set the wipe position by a menu operation
1 Press [Position] in the Key1 Wipe Adjust menu,
turning it on.
2 Set the following parameters.
Knob
Parameter
Adjustment
Setting values
1
Position H
Horizontal
position
–200.00 to
+200.00
a)
2
Position V
Vertical position
–200.00 to
+200.00
a)
a) See page 169.
To move the pattern from its current position to
the center through the course of a transition
Press [Auto Center], turning it on.
Rotating the wipe pattern (Rotation)
1 In the <Rotation> group of the Key1 Wipe Adjust
menu, select the rotation type.
Angle: Incline the pattern through a fixed angle.
Speed: Rotate at a speed rate.
Magnitude: Rotate the pattern through a fixed angle
during the course of the transition.
2 According to the selection in step 1, set the following
parameters.
When Angle is selected
Knob
Parameter
Adjustment
Setting values
1
Angle
Angle of pattern
rotation
–100.00 to
+100.00
a)
a) See page 170.
When Speed is selected
Knob
Parameter
Adjustment
Setting values
1
Speed
Rotation rate of
pattern
–100.00 to
+100.00
a)
a) See page 170.
When Magnitude is selected