Sony SS-HW1 User Manual

SS-HW1
© 2014 Sony Corporation
Printed in China
English
Features
WD (Wide Dispersion) super tweeters on the
front and top provide a multidirectional
listening experience. That way, high-quality
sound from sound sources or CDs can be
enjoyed in wider area than with conventional
speakers.
Attaching speaker pads
Attach the supplied speaker pads to the
bottom of the speakers to prevent slipping.
Connections
 Before connecting, turn off the amplifier to
avoid damaging the speaker system.
 When turning the amplifier or program
source power on/off, reduce the sound level
on the amplifier to minimum.
 When bass sound is missing or the sound
output position of musical instruments is
not distinct, make sure the +/– terminals of
speaker cords are connected properly.
Precautions
 Avoid driving the speaker system
continuously with a wattage exceeding the
maximum input power of each speaker.
 Do not place anything on the speakers.
 Do not attempt to open the enclosure or
remove speaker units. There are no
user-serviceable parts inside.
 Keep recorded tapes, watches, personal credit
cards, and hard disk drives using magnetic
coding away from the speaker system.
 The speaker system has been tuned without
the grille on. Remove the grille before using
the speaker system.
Cleaning and maintenance
 To avoid damaging the enclosure, do not
use thinner, alcohol, benzene, etc.
 To keep a good gloss on the enclosure, dust
it first using a soft cloth, a brush, or a feather
duster and then polish it using a dry
cleaning cloth (never use a scrubbing brush
or a sponge).
 Wipe the surface gently. For fingerprints or
oil stains, etc., breathe on the surface and
wipe it off with a cleaning cloth.
 If the enclosure becomes extremely dirty,
wipe the enclosure using a soft cloth slightly
moistened with a soap and water mix.
 Be careful not to scratch the surface of the
enclosure.
 Wipe dust and other dirt from the WD (Wide
Dispersion) super tweeter (top panel) using
a blower brush or soft brush.
Speaker Placement
 Please note that room acoustics can often
produce large difference in the sound for
small changes in speaker placement.
 Place the speaker system against a hard
wall with its back about 20cm away from
a wall.
 Place the right and left speakers in a
similar acoustic environment.
Speaker System
Operating Instructions
Mode d’emploi
사용설명서
4-534-167-21(1)
 Do not place the speaker system in the
following places:
 Anywhere that is extremely hot or under
direct sunlight
 Anywhere that is dusty
 Anywhere that is extremely humid
 Near a player
 In a cabinet, especially one above your line
of sight
About the 13 cm woofer cone
Black spots on the woofer cone surface occur
naturally in the mica used for the cone
material. They do not affect the sound/
characteristics of the speaker.
Specifications
Speaker system 3 way, 4 drivers speaker
system
Loud speaker units Woofer: 13cm, cone type (1)
Tweeter: 2.5cm, soft dome
type (1)
Super tweeter: 1.9cm, soft
dome type (2)
Enclosure type Bass reflex
Rated impedance 4ohms
Maximum input power 100watts
Sensitivity level 83 dB (2.83 V, 1 m)
Effective Frequency Range 50 Hz - 50 kHz
Dimensions (w/h/d) Approx. 171mm × 309mm ×
273mm
Mass Approx. 5.1kg
Supplied accessories Speaker cords (2)
Speaker pads (8)
Operating Instructions (1)
Design and specifications are subject to change
without notice.
Connection/Raccordement/
연결
Speaker cord (supplied)
Cordon d’enceinte (fourni)
스피커 코드(부속품)
Speaker cord (supplied)
Cordon d’enceinte (fourni)
스피커 코드(부속품)
 Output power of your receiver or amplifier must not be over the maximum input power of
the speaker system, and an appropriate volume level to prevent sound distortion must be
kept. See “Specifications” for the maximum input power.
 La puissance de sortie de votre récepteur ou de votre amplificateur ne pas doit être
supérieure à la puissance d’entrée maximum du système d’enceintes, et vous devez
maintenir le volume à un niveau approprié afin d’éviter la distorsion. Voir la section
«Spécifications» pour connaître la puissance d’entrée maximum.
Right
Droit
오른쪽
+ terminal (red)
Borne + (rouge)
+ 단자(빨간색)
– terminal (black)
Borne – (noire)
- 단자(검은색)
Amplifier
Amplificateur
앰프
Left
Gauche
왼쪽
 리시버 또는 앰프의 출력이 스피커 시스템의 최대 입력을 초과하면 안되며, 적정 음량을 유지해서
사운드가 왜곡되지 않게 해야 합니다. 최대 입력은 "사양"을 참조하십시오.

Sony SS-HW1 Specifications

General

Speaker Type	Bookshelf
Enclosure Type	Bass reflex
Power Handling	100 W
Speaker Units	13 cm cone woofer, 2.5 cm dome tweeter
Frequency Response	45 Hz - 50 kHz
Dimensions (W x H x D)	200 x 350 x 265 mm