Need help?Do you have a question about the Source Audio Soundblox Pro and is the answer not in the manual?
General| Type | Multi-Effects Processor |
|---|---|
| Technology | Digital |
| Input Impedance | 1 MΩ |
| Output Impedance | 100 Ω |
| Inputs | 1 x 1/4" instrument input |
| Power Source | DC power supply |
| Current Draw | 300 mA |
| Effect Type | Various |
| MIDI | In |
| Power Supply | 9V DC |
| Controls | Footswitches |
Features 23 types of envelope filter and phaser effects for a wide sonic range.
Offers bass-optimized envelope follower with adjustable sweep and speed.
Features a thoughtfully designed, rugged, and sleek enclosure.
Utilizes a proprietary 56-bit DSP (SA601) and 24-bit converters for clear audio.
Unique algorithm preserves low-end bass frequencies, avoiding 'tone suck'.
Allows saving and quick access to 6 user presets in two banks via 3 footswitches.
Provides an ultra-precise 7-band graphic equalizer for detailed tone control.
Filter effects modulated by envelope follower, LFO, expression pedal, or Hot Hand sensor.
Provides access to advanced control functions like LFO shapes and expression pedal routing.
Ensures zero signal degradation with bypass routed around the DSP.
Connect the included 9V DC adapter to the 9V DC jack (A).
Connect instrument to GUITAR IN (B) and amp to GUITAR OUT (C) using 1/4" cables.
Connect an optional Hot Hand sensor to the SENSOR IN (D) jack.
Overview of controls A (Effect), B (Sweep Range), and C (Frequency).
Controls attack/decay speed, LFO rate, or Hot Hand sensitivity/axis.
Adjusts the ratio of dry to wet signals, with LO-RETAIN option.
Selects between preset banks A (1-3) and B (4-6).
Selects modulation source: ENVELOPE, LFO, or HOT HAND.
Enables tap tempo functionality for LFO speed control.
Allows editing of EQ bands using buttons and knob.
Engage presets, bypass, save edited presets, and set tap tempo.
Responds to signal amplitude for auto-wah effects.
Creates rhythmic pulses or sweeps for oscillating filter effects.
Uses accelerometer data from a wearable ring for filter modulation.
Controls various parameters like filter modulation or LFO speed.
Preserves low-end frequencies, avoiding 'tone suck'.
Connect bass guitar or instrument using a standard MONO 1/4" cable.
Connect to your amplifier, pedal, or other audio device.
Connect a passive expression pedal with a TRS plug.
Connect an optional Hot Hand sensor (wired or wireless).
Use for daisy-chaining to another pedal's sensor input.
Connect to MIDI output for program changes and continuous control.
Connect the included 9 Volt DC power supply here.
Selects one of 23 filter types or EQ ONLY mode.
Controls sweep direction and breadth (Envelope/Hot Hand) or depth (LFO).
Sets the center frequency of the filter sweep.
Controls attack/decay speed, LFO rate, or Hot Hand sensitivity.
Adjusts the ratio of dry to wet signals.
Buttons to select the frequency band for the equalizer.
Adjusts the value of the selected EQ band by 1 dB steps.
Switches between preset banks A (1-3) and B (4-6).
Selects modulation source: Envelope, LFO, or Hot Hand.
Enables Tap Tempo mode for LFO speed synchronization.
Rightmost footswitch sets LFO speed by rhythmic tapping.
Describes resonant low-pass filters with various Q values and notch characteristics.
Details four-pole low-pass filters with different peak and slope characteristics.
Features peak frequency response with moderate or high Q settings.
Describes filters with three moving peaks, together or in opposing directions.
Covers filter types with combinations of peaks and notches in their response.
Details two and three notch phaser effects with varying feedback levels.
Bypasses filter effects to use the BEF Pro solely as a 7-band equalizer.
Connect and utilize an expression pedal for manual filter modulation and parameter control.
Information on Hot Hand motion sensors and their connection to the BEF Pro.
Procedure to calibrate the Hot Hand sensor for optimal filter sweep control.
Details MIDI messages for preset selection and parameter control via MIDI.
How to enter and exit Backpage mode for advanced parameter access.
Adjusts the range or depth of the expression pedal input.
Selects destination for expression pedal or LFO modulation.
Lists the 13 possible 'XC' destinations for modulation control.
Enables an 8-band EQ mode with an additional high-frequency band.
Adjusts the final output signal level of the pedal.
Modifies filter sharpness, affecting frequency response peaks and notches.
Determines if EQ affects only wet signal or both wet and dry signals.
Selects from nine different LFO waveforms for modulation.
Assigns MIDI channels (1-16) to the effect knob.
Procedure to reset the pedal to its original factory defaults.
Physical size details: Length, Width, and Height.
Specifies the total weight of the unit.
Details power requirements: voltage, polarity, and current draw.
Lists technical audio specifications like ADC/DAC, DNR, and bypass type.
Troubleshooting steps for addressing unwanted noise in the audio signal.
Guidance for resolving issues with the Hot Hand sensor functionality.
Steps to diagnose and fix problems with control knobs.
Details service, repair, and return authorization procedures.
Outlines warranty limitations, exclusions, and legal disclaimers.
To Next Page
