Stanley FATMAX V20 LITHIUM ION SFMCGA75 - Page 6

6
ENGLISH
(Original instructions)
f. Do not expose a battery pack or tool to re or
excessive temperature.Exposuretoreortemperature
above 130 °C may cause explosion.
g. Follow all charging instructions and do not charge the
battery pack or tool outside the temperature range
specied in the instructions. Charging improperly or at
temperaturesoutsidethespeciedrangemaydamagethe
batteryandincreasetheriskofre.
6. Service
a. Have your power tool serviced by a qualied repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
b. Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
Additional power tool safety warnings
@
Warning! Additional safety warnings for Augers
and mixers.
u Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring. Fasteners
contacting a "live" wire may make exposed metal parts
of the power tool "live" and could give the operator an
electric shock.
u Use the auxiliary handle(s). Loss of control can cause
personalinjury
u Never operate at higher speed than the maximum
speed rating of the drill bit. At higher speeds, the bit is
likely to bend if allowed to rotate freely without contacting
theworkpiece,resultinginpersonalinjury.
u Always start drilling at low speed and with the bit tip
in contact with the workpiece. At higher speeds, the bit
is likely to bend if allowed to rotate freely without
 contactingtheworkpiece,resultinginpersonalinjury.
u Apply pressure only in direct line with the bit and do
not apply excessive pressure. Bits can bend causing
breakage or loss of control, resulting in personal
 injury.
u The intended use is described in this instruction
manual. The use of any accessory or attachment or per-
formance of any operation with this tool other than those
recommended in this instruction manual may present a
riskofpersonalinjuryand/ordamagetoproperty.
Safety of others
u This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
u Children should be supervised to ensure that they do not
play with the appliance.
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
u Injuriescausedbytouchinganyrotating/movingparts.
u Injuriescausedwhenchanginganyparts,bladesor
accessories.
u Injuriescausedbyprolongeduseofatool.Whenusing
any tool for prolonged periods ensure you take regular
breaks.
u Impairment of hearing.
u Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Vibration
The declared vibration emission values and the declared
noise emission value(s) stated in the technical data and the
declaration of conformity have been measured in accordance
with a standard test method provided by EN62841 and may
be used for comparing one tool with another.
The declared vibration emission value and the declared
noise emission value(s) may also be used in a preliminary
assessment of exposure.
Warning! The vibration and noise emission value during
actual use of the power tool can differ from the declared value
depending on the ways in which the tool is used. The vibration
level may increase above the level stated.
When assessing vibration exposure to determine safety
measuresrequiredby2002/44/ECtoprotectpersonsregularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of
the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to the
trigger time.
Labels on tool
The following symbols are shown on the tool along with the
date code:
:
Warning!Toreducetheriskofinjury,theuser
must read the instruction manual.