Star Micronics TSP700 Series - Page 49

15-8
[*4] • MSW3-F to 8 Code Page Details
MSW3-F MSW3-E MSW3-D MSW3-C MSW3-B MSW3-A MSW3-9 MSW3-8
Character Table
0 0 0 0 0 0 0 0 Normal*
0 0 0 0 0 0 0 1 CodePage437 (USA,Std. Europe)
0 0 0 0 0 0 1 0 Katakana
0 0 0 0 0 0 1 1 CodePage437 (USA,Std. Europe)
0 0 0 0 0 1 0 0 Codepage 858 (Multilingual)
0 0 0 0 0 1 0 1 Codepage 852 (Latin-2)
0 0 0 0 0 1 1 0 Codepage 860 (Portuguese)
0 0 0 0 0 1 1 1 Codepage 861 (Icelandic)
0 0 0 0 1 0 0 0 Codepage 863 (Canadian French)
0 0 0 0 1 0 0 1 Codepage 865 (Nordic)
0 0 0 0 1 0 1 0 Codepage 866 (Cyrillic Russian)
0 0 0 0 1 0 1 1 Codepage 855 (Cyrillic Bulgarian)
0 0 0 0 1 1 0 0 Codepage 857 (Turkish)
0 0 0 0 1 1 0 1 Codepage 862 (Hebrew)
0 0 0 0 1 1 1 0 Codepage 864 (Arabic)
0 0 0 0 1 1 1 1 Codepage 737 (Greek)
0 0 0 1 0 0 0 0 Codepage 851 (Greek)
0 0 0 1 0 0 0 1 Codepage 869 (Greek)
0 0 0 1 0 0 1 0 Codepage 928 (Greek)
0 0 0 1 0 0 1 1 Codepage 772 (Lithuanian)
0 0 0 1 0 1 0 0 Codepage 774 (Lithuanian)
0 0 0 1 0 1 0 1 Codepage 874 (Thai)
0 0 1 0 0 0 0 0 Codepage 1252 (Windows Latin-1)
0 0 1 0 0 0 0 1 Codepage 1250 (Windows Latin-2)
0 0 1 0 0 0 1 0 Codepage 1251 (Windows Cyrillic)
0 1 0 0 0 0 0 0 Codepage 3840 (IBM-Russian)
0 1 0 0 0 0 0 1 Codepage 3841 (Gost)
0 1 0 0 0 0 1 0 Codepage 3843 (Polish)
0 1 0 0 0 0 1 1 Codepage 3844 (CS2)
0 1 0 0 0 1 0 0 Codepage 3845 (Hungarian)
0 1 0 0 0 1 0 1 Codepgae 3846 (Turkish)
0 1 0 0 0 1 1 0 Codepage 3847 (Brazil-ABNT)
0 1 0 0 0 1 1 1 Codepage 3848 (Brazil-ABICOMP)
0 1 0 0 1 0 0 0 Codepage 1001 (Arabic)
0 1 0 0 1 0 0 1 Codepage 2001 (Lithuanian-KBL)
0 1 0 0 1 0 1 0 Codepage 3001 (Estonian-1)
0 1 0 0 1 0 1 1 Codepage 3002 (Estonian-2)
0 1 0 0 1 1 0 0 Codepage 3011 (Latvian-1)
0 1 0 0 1 1 0 1 Codepage 3012 (Latvian-2)
0 1 0 0 1 1 1 0 Codepage 3021 (Bulgarian)
0 1 0 0 1 1 1 1 Codepage 3041 (Maltese)
1 1 1 1 1 1 1 1 User Setting (Blank Code Page)
• When MSW3-F to 8 is out of the definition, Normal is selected.
[STAR Line Mode]
The code page initial value is selected using this memory switch setting.
These settings are enabled only on overseas models.
This can be specified using the command: ESC GS t n.
(See the Command description for details.)
[ESC/POS Mode]
Not selectable by memory switches. Code page initial value is fixed to Code Page 437.
This can be specified using the ESC/POS command: ESC t n.
(See the Command description for details.)
This can be specified using the STAR command: ESC GS t n.
(See the Command description for details.)
<Blank Code Page>
The registered code page is selected using this command. A space is registered at ex-factory.