Stevens ROAD - Bicycle Transport: Cases and Cartons

S - 100 | English English | S - 101
Note:
For your own safety, bring your newly purchased STEVENS bicycle to the STEVENS dealer for its first
service after 100 to 300 kilometres (60 to 180 miles), 5 to 15 hours of use or four to six weeks, at the very
latest, however, after three months.
Component What to do Before
every ride
Monthly Annually Others
Painted/anodised/carbon
surfaces
Polish × at least every
6months
Wheels/spokes Check for trueness and tension ×
True or retighten • if necessary
Handlebar and stem (made
of aluminium and carbon)
Check and replace, if necessary • every 2years
at the latest
Headset Check for bearing play ×
Regrease
•
Metal surfaces Polish (except:
rim sides of rim brakes, rotors)
× at least every
6months
Hubs Check for bearing play ×
Regrease
•
Pedals (all) Check for bearing play ×
Pedals (clipless) Clean and grease locking mechanism ×
Seat post/stem Check bolts ×
Disassemble and regrease
Carbon: new assembly paste
(no grease!)
•
Front/rear derailleur Clean and grease ×
Quick-releases/
thru axles
Check seat ×
Bolts and nuts
(mudguards etc.)
Check and retighten, if necessary ×
Software Update • if offered by the
manufacturer
Valves Check seat ×
Cables gears/brakes Dismount and regrease
•
If you have a certain degree of mechanical skills, experience and suitable tools, such as a torque wrench, you
should be able to do the checks marked × by yourself. If you will come across any defects, take appropriate meas-
ures without delay. If you are in doubt or if you have any questions, contact your STEVENS dealer.
Jobs marked • are best left to your STEVENS dealer.
Recommended Torque Settings
All bolted connections of the bicycle components have to be tightened carefully and checked regularly to ensure
the safe and reliable operation of your STEVENS bicycle. This is best done with a torque wrench that disengages at
the desired torque value or a click-type torque wrench. Tighten carefully by approaching the prescribed maximum
torque value in small steps (0.5 Nm increments) and check in between the proper fit of the component. Do not
exceed the maximum torque value indicated by the manufacturer!
Where no maximum torque value is given start with 2Nm. Observe the indicated values and observe the values
on the components themselves and/or in the instructions of the component manufacturers.
Component Bolted connections Shimano
1
(Nm)
SRAM/Avid
2
(Nm)
Campagnolo
3
(Nm)
Rear derailleur Mount (on frame/derailleur hanger) 8–10 8–10 15
Cable clamp 5–7 4–5 6
Pulley wheels 3–4
Front derailleur Mount on frame 5–7 5–7 5 (clamp)
7 (direct mounting)
Cable clamp 5–7 5 5
Brake levers/
shifter units
Mount on handlebar 6–8 5–7 10
Flatbar 0.3–0.5 6
Hub Quick-release lever 5 –7.5
Locknut for bearing adjustment of quick-re
-
lease hubs
10–25
Sprocket cluster lock ring 29–49 40 40 (11-speed)
50 (10-speed)
Internal gear hub Axle nut 30–45
Crank Crank mount (grease-free square-head) 35–50 32–38
Crank mount (Shimano Octalink) 35–50
Crank mount (Shimano Hollowtech II) 12–15
Crank mount (Isis) 31–34
Crank mount (Gigapipe) 48–54
Spline 42
Chainring mount 8–11 12–14 (steel)
8–9 (alu)
8
Sealed cartridge
bearing
Shell (square-head) 49–69 70
Shell
(Shimano Hollowtech II, SRAM Gigapipe)
35–50 34–41
Octalink 50–70
Pedal Pedal axle 35 40
Shoe Cleat 5–6
Spike 4
1
https://si.shimano.com
2
www.sram.com
3
www.campagnolo.com