STIEBEL ELTRON HDB-E 11/13 Trend - Data Table

INSTALLATION
Specification
17.8 Data table
HDB-E 11/13 Trend HDB-E 18 Trend 25A HDB-E 18/21/24 Trend HDB-E 27 Trend
204208 207040 204209 204210
Electrical data
Rated voltage
Rated output
Rated current
V 380 400 380 400 380 400 380 400
kW 9.9/12.2 11/13.5 16.2 18 16.2/19/21.7 18/21/24 24.4 27
A 16.6/18.5 17.5/19.5 24.7 26 27.6/29.5/33.3 29/31/35 37.1 39
Fuse protection
Frequency
Phases
A 20 20 25 25 32/32/35 32/32/35 40 40
Hz 50/60 50/60 50/60 50/60 50/60 50/60 50/- 50/-
3/PE 3/PE 3/PE 3/PE
Resistivity p15
Conductivity an 5
Max. mains impedance at 50 Hz
Versions
O cm 900 900 900 900
pS/cm 1111 1111 1111 1111
0.456 0.434 0.329 0.313 0.247 0.235 0.220 0.209
Heating system, heat generator
Insulating block
Adjustable connected load
Temperature setting
Protection class
Bare wire Bare wire Bare wire Bare wire
Plastic Plastic Plastic Plastic
°C 35, 43, 50, 55* 35, 43, 50, 55* 35, 43, 50, 55* 35, 43, 50, 55*
1 1 1 1
Cover and back panel
IP rating
Colour
Plastic Plastic Plastic Plastic
IP 25 IP 25 IP 25 IP 25
white white white white
Connections
Water connection G 1/2 G 1/2 G 1/2 G 1/2
Application limits
Max. permissible pressure MPa 1 1 1 1
Values
Max. inlet temperature ( e.g. pasteurisation) °C 70 70 70 70
On l/min > 2.5 > 2.5 > 2.5 > 2.5
Flow rate limit at l/min 4.0 8.0 8.0 9.0
Flow rate at 28 K l/min 5.6/6.9 ( 400 V) 9.2 ( 400 V) 9.2/10.7/12.3 ( 400 V) 13.8 ( 400 V)
Flow rate at 50 K l/min 3.2/3.9 ( 400 V) 5.2 ( 400 V) 5.2/6.0/6.9 ( 400 V) 7.7 ( 400 V)
Pressure drop for flow rate at 50 K ( without flow limiter) MPa 0.03/0.04 0.06 0.06/0.08/0.1 0.13
Pressure drop for flow rate at 50 K ( with flow limiter) MPa 0.08/0.2 0.1 0.1/0.13/0.17 0.2
Hydraulic data
Nominal capacity I 0.4 0.4 0.4 0.4
Dimensions
Height
Width
MM 466 466 466 466
MM 225 225 225 225
Depth
Weights
Weight
MM 105 105 105 105
2.80 2.90
* The temperatures are relative to a rated voltage of 400 V.
Notice
The appliance conforms to IEC 61000 -3- 12.
2.90 2.90
40 I HDB-E Trend www.stiebel-eltron.com