SunStar Fortuna 5 Series - Pattern Work and Chain Functions

(9) Method of Use: Pattern Work Selection Button
A Method to Set Up the Pattern Woik FuncUon
This function is used when you need to continuously work on a sewing material. If the
light goes on after pressing the button, you can use the pattem sewing function.
PATTERN
8. Method of Use of Pattem Sewing Specific Functions
® Cautionary words when using the pattem function
• Before using the pattem function, finish the trimming work and turn on the pattem switch light.
• If the user presses the pattem switch twice when he/she is not using the pattem function, the light will go off and he/she will be
able to go back to normal sewing. However, if the pattem mode has not been completely finished, the pattem light will not go
off.
• The pattem function sewing speed will be the programmed speed.
• The value set in each pattem mode is not erased when the power is turned off Therefore, if you want to use the same pattem
again, press the same mode again to use it. However, if the program is initialized, all the formerly programmed information will
be erased and the user must reset the information again.
(2) Method of use:
function
<SCTeen showing thef programming of
^ - . ft 1 . . . . . .. . stitch numbers fo r each side>
(a) first press the I I button and select the pattem sewmg function.
® Select the pattem you want and the light will go on the pattem you selected. l^^ll
© If you press the ^ button, the screen will change and you can use the stitches of | " U IILJ i|
each side of the pattem you chose to program the value.
< Method to program the value of each pattem side >
• Method by using the O' O buttons 1^^^
- Inputting directly the number of stitch the user wants by using the buttons C and D. | M U | |LJ i|
This method is used when the user already knows the length of the stitches he/she
is choosing.
- Method using the pedal movement 1^ • VVhen the AUTO light is off, the machine
TL- • f ,• j L ,1. j ,. 1 ,1. L1 j stops when the pedal is released while
- This IS a function used when the user does not know the stitch length and sews sev^ng
directly to check the number of stitches for the pattem he/she wishes to program. If A: When the AUTO light is on, hie machine
the user presses on the pedal after the programming screen comes on, the pedal can will finish sewing the pattem section even if
program the number of stitches by using the accelerating and decelerating user releases pedal while sewing,
characteristics through the pedal's sensors. The standard for choosing the number
of stitches here is slower than the normal sewing speed and the programmed
pattem sewing speed.
- Method using the A button and 1/2 stitch button
- This function is used when the user needs to make small adjustments at the end of
the pattem work. It allows the user to check and program the pattern length while
he/she sews at a slow speed or sews half stitches.
® After programming is finished, press the 0 button and save die set up value. Then press the
0 button. After the stitch numbers of each side disappear fr om the screen, you can start
sewing with the prc^rammed value in the pattern sewing function.
® The pattem sewing speed is constant because it sews at a programmed speed not by the
acceleration or deceleration of the pedal. If you press the pedal after pressing the °0 button and
see the li^t blink, sewing will continue until it Is finished even if jou release the pedal.
^ > I ■ , I I -
A I • After setting each side of the stitches, the user must press the © button to save the programmed value.
I * When the pattem has more ft ian one side, the pattem work only operates for the number of stitches programmed
l^ution I for each side.
niin {
u llu I
P : When the AUTO light is off, the machine
stops when the pedal is released while
sewing.
A: When the AUTO light is on, tt ie machine
will finish sewing the pattem section even if
user releases pedal while sewing.
From the library of Superior Sewing Machine & Supply LLC - www.supsew.com