SunStar Fortuna 5 Series - Group B: Output, Timing, and Thread Trimming

—(
^^inStar
(2) Group B Parameter: All types of output, Full-on Tlme/PWM Duty, checking input/output operations, sewing
machine models and thread trimming sequence programming.
^ These are functions not used by general users and must be regulated by an NS technician.
No.
Function Initial v^ue Range Step . 1
1 Back Tack Solenoid Initial Full On Time
1020ms 4-1020 4ms
2 Presser Foot-Lift Solenoid Initial Full On Time
200ms 4-1020
4ms
3 in Solenoid Initial Full On Time
100ms 4-1020 4ms
4 Wiper Solenoid Initial Full On Time 100ms
4-1020
4ms
5 Tension Release Solenoid initial Full On Time
100ms 4-1020 4ms
6 Left Solenoid Initial Full On Time (For Twin Needle)
100ms 4-1020 4ms
7 Right Solenoid Initial Full On Time (For Twin Needle)
100ms 4-1020 4ms
8
Auxiliary Solenoid Initial Full On Time 100ms 4-1020 4ms
9 Left LED Initial Full On Time {FcxTwin Needle)
100ms 4-1020 4ms
10
Right LED Initial Full On Time (For Twin Needle) 100ms 4-1020 4t7rs
11 Needle plate up-stop signal Initial Full On Time
100ms 4-1020 4ms
12 Needle plate down-stop signal Initial Full On Time
100ms 4-1020
4ms
13
Signal notifying motor running Full On Time 100ms 4-1020 4ms
14 Signal notifying target speed achieved Full On Time
100ms 4-1020
4ms
15 Back Tack Solenoid Duty Ratio 50%
0-100
10%
16 Presser Foot-Lift Solenoid Duty Ratio
20% 0-100 10
17
Thread Trimming Solenoid Duty Ratio , 100 0-100 10
18 Wiper Sdenoid Duty Ratio i
100 0-100 10
19 Tension Release Solencxd Duty Ratio
100 0-100 10
20
Left Solaioid Duty Ratio (For Twin Needle) i 50 0-100 10
21
Right Solenoid Duty Ratio (For Twin Needle) ' 50 0-100 10
22 Aux Solenoid Duty Ratio 100 0-100 10
23 Left L£D Duty Ratio (For Twin Needle)
100 0-100 ! 10
24
Right LED Duty Ratio (For Twin Needle) 100 0-100
10
25 Signal fo r up stopping needle Duty Ratio 100 0-100 10
26 Signal fo r low stopping needle Duty Ratio
100
0-100 10
27 Signal notifying motor running Duty Ratio 100 0-100 ! 10
28
Signal notifying target speed reached Duty Ratio 100 0-100 1
10
29
NOT USED
1 1 1
30 Start Back Tack A numt)ef of stitches correction value
00.30
6-6 ■ 0.05 stitch
31 Start Back Tack B numt>er of stitches correction value 00.30 6-6
0.05 Stitch
32 End Back Tack C stitch correction value 00.40 6-6 0.05 Stitch
33 ; End Back Tack D stitch correction value 00.40 6-6
0.05 Stitch
34 1
Seledion fo r maintaining reverse solenoid movement when Ihread trimming (C Only B/T)
0 0/1
1=reverse direction maintained
35 Programming count condition
(program whether or not automatic counter will be operated)
0/1
0=counter used
l^automatic counter after ti vead trimming
36
When automatically counting, select Up/Down count after thread
trimming (thread trimming function must be enabled)
1 0/1
1=Up COUNT
0=DOWN COUNT
37 When count in completeded, the next operation is programmed
0
0/1/2
0=tHizzer rings, sewing is slowed
1 =txizzer lings, sewing is not allowed
(If you press the Prog Key, set up is cancelled)
2=No buzzer ri ng, sewing is allowed
38
When count is completed, select the counter auto dear/preset 0/1
1=AUT0
CLEAR/PRESET
NOT USED
: Items No. 30-33: These are Wie items that make the numtjer of stitches match when back tack number of stitches do not match.
: Solenoid Duty Ratio: The power ti iat holds and maintains the solenoid.
Solenoid Initial full on tme; The ti me It takes to pull the solenoid to the maximum In the outset.
A
If the specific Items of the parameter are changed carelessly, they could break down or damage the machine, so the
user must be well-trained before using It.
From the library of Superior Sewing Machine & Supply LLC - www.supsew.com