SunStar Fortuna 5 Series - Page 63

fntiiiHtar
(3) Group C Parameter: Pedal acceleration/deceieration curve, slow starting speed and input/output port change
related parameter
^ TTiese are functions not used by general users and must be regulated by an after-sales service engineer.
Function Initial value Range Step
1 1 step section where pedal moves forward
10 0-64
1
2 2 step section where pedal moves forward
15 0-64 1
3
3 step section where pedal moves forward 31 0-64 1
4
4 step section where pedal moves forward
40 0-64 1
5 5 step section where pedal moves forward
52 0-64 1
6 Sewing speed value In the 1 step where pedal moves forward
440spm 40-9960
40spm
7
Sewing speed value in the 2 step where pedal moves forward 920spm 40-9960 40spm
8 Sewing speed value in the 3 st^ where pedal moves forward 4000spm 40-9960 40^
9
Sewing speed value in the 4 step where pedal moves forward
5480^ 40-9960 40spm
10 Sewing speed value in the 5 step where pedal moves fbiward 9960^m 40-9960 40spm
11
Select slow start after thread trimming
(After performing thread trimming, start the next severing work slowly)
0
0/1 1=selection
12
Select slow start after sewing machine stops
(After performing sewing machine stops, start the next sewing work slowly)
0 0/1
1=sele(aion
13 When starting slowly, select sewing speed diange 0 0/1
1=UseC14-C18 value
0=Use default value
14 The speed of the firet stitch when starting slow 400^ 40-9960 40spm
15 The speed of the second stitch when starting slow 400^ 40-9960 40spm
16 The speed of the third stitch v4ien starting slow 640spm 40-9960 40^
17 The speed of the fourth stitch when starting slow lOOOspm 40-9960 40spm
18
The speed of the fifth stitch when starting slow
1680spm 40-9960 40spm
19 Limited maximum motor speed
SOOOrpm 20-3400 20rpm
20 Synchronizer sensor rotation sensing ti me 40x0.1sec 5-1275
0.5sec
21
Overload sensing time SOxO.lsec
5-1275 O.Ssec
22 Solenoid electric overflow sensing ti me 100ms 4-1020 4ms
23 Power off sensing time 4ms 4-1020 4ms
24
NOT USED
25 Bad siqinal of the Encoder A and B phase detectino number of time
4 1-255 1
26 Back siainal of the Encoder R. S and T phase detectino number of time 4 1-255
1
27 Bad siainal of the Encoder R, 8 and T phase detectino number of ti me
4 1-255 1
28 NOT USED
29
• Automatic scaling to the speed curve selected by each set mode
- Mode 0: Use a curve based on the set values from C-1 to C-10
- Mode 1: Scaling to the speed set at A-2
- Mode 2; Scaling to the speed set using the Speed Up/Dn key
1 1-2
1
y^\ Items No. 1~5 : Equal division of pedal stroke in 64 steps, The speed curve of the pedal
i 1 stroke changes according to how many steps are set up for the divided
j/j 1 I M 1 pedal stroke of each forward pedal step. (Used when adjusting pedal
jr I I I f i I { V
I ! I ! M I sensor)
Pedid Stnls
^ No. 20: If a synchronizer signal comes, but the next synchronizer signal does not come within the sensing ti me, an error
message will appear.
^ No. 21 : If a speed instruction was sent to the motor but the motor does not reach the value of the speed instnjction, an error
message will appear.
A I If the specific items of the parameter are changed carelessly, they could break down or damage the machine, so the
1 user must be well-trained before using it
From the library of Superior Sewing Machine & Supply LLC - www.supsew.com