Suptek SPM201XL - User Manual

To Next Page

SPM201XL

INSTALLATION MANUAL

Supplied parts list

Tools Required

Before you start

·Phillips Screwdriver ·carpenter’s level

·3.8MM drill bit ·8MM masonry bit

Mounting the wall bracket to the wall

Optional Speaker Wire

Management

Step 1

This pack contains 2 speaker mounts

Suitable for loads up to 30kg（66lbs）each speaker

UNPACKING INSTRUCTIONS

Carefully open the carton, remove contents and lay out on cardboard

or other protective surface to avoid damage.

Check package contents against the Supplied Parts List in the next

page to assure that all components were received undamaged. Do

not use damaged or defective parts.

Carefully read all instructions before attempting installation.

IMPORTANT SAFETY INFORMATION

Install and operate this device with care. Please read this instruction

before beginning the installation, and carefully follow all instructions

contained herein. Use proper safely equipment during installation.

Please call a qualified installation contractor for help if you:

If you don’t understand these directions or have any doubts about the

safely of the installation.

If you are uncertain about the nature of your wall, consult a qualified

installation contractor.

Do not use this product for any purpose or in any configuration not

explicitly specified in this instruction. We hereby disclaims any and all

liability for injury or damage arising from incorrect assembly, incorrect

mounting, or incorrect use of this product.

(2)Wall

Bracket-a

(2)Wall Bracket

Cover-b

(2)Tilting End Cap-c (2)Speaker

Platform-d

(2)M8x60mm

Bolt-e

(2)Plastic Washer-f (2)M8 Washer-g (2)M8 Nut-h

(10)M4x12mm

Wood Screw-i

(8) M6x45mm

Lag Bolt-j

(1)wrench-m

(8)Lag Bolt

Washer-k

(8)M8x40mm

Concrete Anchor-l

Option A : Wires are concealed inside the wall

Option B : Wires are exposed outside the wall

Note: The mounting components and hardware supplied in this

package are not designed for installations to walls with steel

studs or to cinder block walls. If the hardware you need for

installation is not included, please consult your local hardware

store for proper mounting hardware for the application.

Need help?

Do you have a question about the Suptek SPM201XL and is the answer not in the manual?

This document describes the Suptek SPM201XL speaker mount, designed to securely hold speakers with a maximum load capacity of 30kg (66lbs) per mount. The package includes two speaker mounts.

Function Description:

The Suptek SPM201XL is a wall-mounted speaker bracket system designed to securely hold speakers and allow for adjustment of their position and angle. It consists of a wall bracket, a wall bracket cover, tilting end caps, and a speaker platform. The system supports both brick and wood wall installations, offering flexibility in mounting options. It also provides optional features for managing speaker wires, allowing them to be either concealed within the wall or exposed outside. The mount facilitates placing the speaker on a platform and then adjusting clamps to firmly hold it in place. Furthermore, it allows for significant adjustments in tilting angle and horizontal swing to optimize sound direction.

Important Technical Specifications:

Load Capacity: Up to 30kg (66lbs) per speaker mount.
Quantity: Pack contains 2 speaker mounts.
Mounting Compatibility: Designed for brick and wood walls. Not designed for walls with steel studs or cinder blocks.
Speaker Platform Adjustment Range: 238-385mm (horizontal adjustment for speaker width).
Tilting Angle Adjustment: +/- 7.5 degrees.
Swing Angle Adjustment: +/- 45 degrees.
Wall Bracket Dimensions (Brick Mount): Requires drilling at 45mm and 40mm intervals, with an 8mm drill bit.
Wall Bracket Dimensions (Wood Mount): Requires drilling at 45mm intervals, with a 3.8mm drill bit.

Supplied Parts List:

The package includes a comprehensive set of components and hardware for installation:

(2) Wall Bracket-a
(2) Wall Bracket Cover-b
(2) Tilting End Cap-c
(2) Speaker Platform-d
(2) M8x60mm Bolt-e
(2) Plastic Washer-f
(2) M8 Washer-g
(2) M8 Nut-h
(10) M4x12mm Wood Screw-i (for optional speaker securing)
(8) M6x45mm Lag Bolt-j (for wood mount)
(8) Lag Bolt Washer-k (for wood mount)
(8) M8x40mm Concrete Anchor-l (for brick mount)
(1) Wrench-m

Tools Required (Not Supplied):

3.8MM drill bit (for wood mount)
8MM masonry bit (for brick mount)
Phillips Screwdriver
Carpenter's level

Usage Features:

Flexible Mounting: Supports installation on both brick and wood walls, catering to different construction types.
Adjustable Speaker Positioning: The speaker platform can be adjusted horizontally (238-385mm) to accommodate various speaker widths.
Angle Adjustment: Allows for precise tilting (+/- 7.5 degrees) and swinging (+/- 45 degrees) of the speaker, enabling users to direct sound optimally.
Secure Clamping: Features adjustable clamps to firmly hold the speaker in place on the platform, preventing accidental dislodgement.
Optional Speaker Securing: Includes M4x12mm wood screws for an additional layer of security, allowing users to directly attach the speaker to the platform if desired.
Wire Management Options: Offers two methods for managing speaker wires:
- Option A: Wires can be concealed inside the wall for a clean, integrated look.
- Option B: Wires can be exposed outside the wall, suitable for situations where in-wall wiring is not feasible or desired.
Ease of Assembly: The manual provides clear, step-by-step instructions for assembly and installation, making the process straightforward for users.

Maintenance Features:

Durable Construction: While not explicitly detailed, the use of robust hardware (M8 bolts, lag bolts, concrete anchors) suggests a durable design intended for long-term use.
Safety Information: The manual emphasizes important safety information, including the need to read instructions carefully, use proper safety equipment, and consult qualified professionals if uncertain about installation or wall type. This proactive approach helps prevent damage to the product or injury during installation.
Customer Support: The manufacturer provides customer support via email (after-sales@suptekmount.com) for any issues or assistance required, ensuring users can get help if needed.
Hardware Compatibility Note: The manual explicitly states that the supplied hardware is not designed for steel studs or cinder block walls, guiding users to consult local hardware stores for appropriate alternatives if their wall type is not supported. This prevents incorrect installation and potential damage.
Pre-installation Check: Users are instructed to check package contents against the supplied parts list and inspect for damaged or defective parts before installation, promoting a smooth and safe setup process.

Suptek SPM201XL Specifications

General

Brand	Suptek
Model	SPM201XL
Category	Speakers
Language	English