PLEASE UNPACK AND WASH ALL PARTS WITH WARM SOAPY WATER BEFORE FIRST USE.
DISPLAY PANEL
There are three light indicator modes:
White Light - Kettle is in active state.
Red Light - Kettle is heating.
Green Light - Kettle has completed heating and is in Keep Warm mode.
If the display is off, press the Start/Stop button to enter the active state. The display is a
combination of touch buttons and LED lights. There will be a sound prompt every time a button is
pressed, and another sound prompt at the end of an operation.
To Switch Between Celsius and Fahrenheit
Press and Hold “+” and “-” at the same time for 3 seconds, until you hear a beep, and the
temperature unit will switch between Celcius and Fahrenheit.
To Select a Tea Function
• Press the “+” or “–” buttons
To Start or Stop the Kettle
Start/Stop button will start or stop the operation of the Kettle.
FUNCTIONS
Press the “+” or “-” button in the active state to select a tea function, and then press the Start/
Stop button to begin the heating process. The color at the bottom of the kettle will change to red.
When the heating process is complete, the color will turn green and move to the Keep Warm state.
When boiling water, the display will show the temperature changes by 1 F or 1 C.
After the selected water temperature has been reached, the sound prompt will beep one time,
and the kettle will automatically switch to Keep Warm state.
To stop or pause the heating process, press the Start/Stop button. The Kettle will stop heating and
return to the active state, but the chosen tea function will remain selected.
To switch the tea function selection while the water is already heating, press either the “+” or
“-” button.
The light will turn white. After 3 seconds, the Kettle w
ill confirm the new selection. The Kettle has a
tea selection memory function with uninterrupted power supply.
NOTE: Tea function selection cannot be made in Keep Warm state.
KEEP WARM
After the water temperature of tea reaches the standard temperature, it will be automatically
switched to Keep Warm state and with a duration of 60 minutes. To cancel Keep Warm, press the
Start/Stop button, and the Kettle will return to the active state.
The light is green in the Keep Warm state.
STANDBY STATE
If there is no operation for 60 seconds, the Kettle will enter a Standby State. After 60 minutes of the
Keep Warm state, the Kettle enters the Standby State automatically. In the Standby State, all lights
and display are off. When in standby, press any but
ton to go back to active state.
Function
Temperature
(°C)
Temperature
(°F)
Keep Warm
Temperature (°F)
Keep Warm
Time (Min)
Boil
100 212 195 60
Herbal
100 212 195 60
Black
100 212 195 60
Oolong
90 195 165 60
White
85 185 165 60
Green
79 175 165 60
Delicate
71 160 140 60
POURING WATER
USING THE INFUSER
USING THE SPOUT FILTER
Lift the Kettle from the power base and then pour the water.
The Kettle may be stored on the power base when not in use.
NOTE: Ensure the lid is firmly closed. The water will spill if the lid is left open during boiling.
NOTE: Operate carefully when pouring the liquid from your Kettle as contact with boiling liquid
may result in burns.
NOTE: Ensure power supply is turned off when Kettle is not in use.
BOIL-DRY PROTECTION
Should you accidentally allow the Kettle to operate without water; the boil-dry protection will
automatically switch it off. If this should occur, allow the Kettle to cool before filling with cold water
and re-boiling.
Place the infuser into the kettle before starting the heating process. The round edge should face
forward (toward spout) and the flat edge will be in the back (toward handle). Secure Infuser into
holder within the Kettle to ensure it fits squarely. Using a spoon, carefully add tea leaves, loose tea
or tea bags to the tea infuser after the heating process is complete. Securely close the lid. Steep
tea according to tea instructions. Tea should steep an average of 4 minutes. Steeping too long
will cause the tea to become bitter.
Caution: Use extreme caution when adding tea to the tea infuser. The Kettle becomes very hot
during the boiling process. Avoid using fingers or hands directly to add tea to the infuser.
The spout filter can be inserted into the spout of the Kettle to filter out any tea
leaves. To insert
the spout filter, open the lid of the Kettle, and place it in the spout from the inside of the Kettle. To
remove it, gently press down on the plastic tab holding it in place and it will release.
NOTE: Never attempt to insert or remove the spout filter while the Kettle is hot as burns can occur.
Always wait for the Kettle to fully cool before inserting or removing the spout filter. Make sure to
clean the spout filter at regular intervals.
To Previous Page
Loading...